Panasonic KX-HCM8 operating instructions Setting explanation

Page 69

Operating Instructions

Setting explanation

a.

b.

c.

d.

e.

f.

The active time of trigger is set between 9:00 AM to 6:00 PM from Monday to Friday.

When the alarm occurs in the setting time, the images are transferred to FTP server, and the notification is sent to the specified user via e- mail.

The alarm trigger is on when the sensor signal is changed to the [Rising] (GND to Open High) of External Sensor Input of External I/O.

The secondary time is set inactive.

The transferring image size is 160 x 120, and the image quality is standard.

Enables the Pre-alarm and Post-alarm Image Buffering:

Network Camera will transfer Pre-alarm 10 images by one image per minute and Post-alarm 20 images by one image per second when detecting the alarm trigger.

Setting of FTP server:

IP Address — 192.168.0.20 Port No. — 21

Login ID — Panasonic Password — ********

Login timing: Every Time

Upload File name — NetworkCamera

File name and time stamp is named to the file. (Example: NetworkCamera20030101093000000.jpg)

Underlined numbers are "9 h 30 min 00 s 000 ms on January 1, 2003". Data transfer method — Passive Mode

SMTP server address — xxx.xxx.com POP3 server address — xxx.xxx.com Login ID — Panasonic

Password — ********

Mail is sent to "NetworkCamera@xxx.xxx.com" from "Panasonic@xxx.xxx.com".

Subject is [Mail Transfer]. Text is [Alarm was generated].

[For assistance, please call: 1-800-272-7033]

69

Image 69

Contents Network Camera For operation assistance Call IntroductionNetwork Camera Memo TrademarksImportant Safety Instructions Table of Contents Specification and Troubleshooting Technical GuidesIndex 115 Section Getting to Know Network Camera Main FeaturesUpdate Firmware AuthenticationMulti-Language Display System Requirements Authentication window Authentication-System Security FeatureIncluded Accessories Setup CD-ROM Front View Camera Feature LocationsBottom View Rear ViewNetwork Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeType 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemHow to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Default Network Camera Configuration Type Port NoNetwork Parameters Table IP addressEnter winipcfg and click OK. IP configuration window appears How to refer the network parameters from the PCSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the InternetIf Top Page does not appear TopOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Viewing Buffered Image Screen Non Transfer mode Alarm/Timer modeClicking Start Capture ViewerPrimary SecondaryMulti-Camera Screen Setup Setup Camera Setup AdministratorGo to Top Name/TimeEntered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Enter only the number Instructions for the data fieldsDhcp File size of the image DdnsCamera Name/TimeName DateTime Changed AM/PM or 24H AdjustmentAuto Time ZoneClick Security Administrator on Setup Security AdministratorEnable For Setup PasswordRetype Security General User Click Security General User on SetupUser ID List Delete or ModifyNew User Top View Image Instructions for the data fields Top ResolutionImage 160 x Image QualityImage Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm ModeAlarm enable condition Sets the image resolution and image qualityActive Time of Trigger Login timing Data transfer method Over write settingSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup White Balance Power LineFixed Indoor FixedMulti-Camera IP Address or Enable check boxURL * 1 or Host Camera NameExternal Output Control Click External Output Control on SetupIndicator Control Status Click Restart Now RestartUpdate Firmware Click Update Firmware Operating Instructions Click Reset to Factory Default on Setup Click Execute Reset to Factory DefaultTechnical Guides Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Explanation of External I/O Interfacing to the External I/OPin Function External Sensor InputCircuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Items Factory Default Indispensable setting Value Network Default Settings ListImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Specifications Network Camera Specifications DescriptionOther Specification Description SMTP, FTP Troubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window Network window on ISPAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen About Other Troubles View Image Setting window onConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP When you ship the product For product service