Samsung SCC-C6403 instruction manual Color/Bw, Motion DET

Page 16

COLOR/BW

In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.

In AUTO mode, AGC will be displayed as “---“. You can’t adjust the settings manually.

In a poor illumination environment, the IR filter is turned off in the BW mode the its sensitivity increases as high as a black and white camera. On the other hand, the IR filter is turned on and the sensitivity decreases in the COLOR mode.

COLOR : The IR Filter is ON and the screen is normal. You can press the [Enter] key to set the COLOR GAIN LEVEL. And when the AGC function is on, you can set the AGC COLOER LEVEL.

(CAMERA SET)

 

CAMERA ID

OFF

V-SYNC

INT

COLOR/BW

 

AUTO...

MOTION DET

OFF

ZOOM SPEED

3

DIGITAL ZOOM

OFF

DISPLAY ZOOM

OFF

DISPLAY P/T

OFF

Press [Enter]

(AUTO)

BURST

ON

LEVEL

LOW

DURATION

S ------ L

(CAMERA SET)

 

CAMERA ID

OFF

V-SYNC

INT

COLOR/BW

COLOR …

MOTION

OFF

(COLOR)

EXIT

QUIT

RET

E

ZOOM SPEED

3

DIGITAL ZOOM

OFF

DISPLAY ZOOM

OFF

DISPLAY P/T

OFF

EXIT

QUIT

Press [Enter]

GAIN

(0)I--------

AGC COLOR

(0)----I----

RET

 

Caution : If you use an infrared light source while in AUTO mode, AUTO switching malfunction and camera AF malfunction may occur.

MOTION DET

BW

: The IR Filter is OFF and the screen is black and white.

 

(Sensitivity to low light is increased to a level comparable to a black

 

and white camera.)

 

Select BW and press [ENTER] and the additional menu to select

AUTO

BURST ON/OFF will appear.

: Select to automatically switch between the COLOR mode and BW

In MOTION DET, you can set the Motion Detection function, Motion Detection Sensitivity, and the Area of Motion Detection. If the Motion Detection function is set, the movement of an intruder can be detected. When motion is detected, it sets off the Alarm signal of the Controller.

mode depending on the amount of light. In low light conditions, the

IR Filter is turned OFF and the sensitivity to low light is increased

by switching to the BW mode, but in bright light conditions, the IR

Filter is turned ON and the sensitivity is decreased by switching to

the COLOR mode.

Select AUTO and press [ENTER] and the additional menu to select

BW LEVEL and DURATION will appear.

-BURST ON : The color burst signal is output together with black and white composite video signal.

-BURST OFF : The color burst signal is not output.

-LEVEL : You can set the brightness level that changes from COLOR mode to BW mode in 3 steps : LOW, MEDIUM, and HIGH.

-DURATION : Set the HOLDING time for switching between COLOR and BW mode depending the changes in the amount of light. You can set the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).

(CAMERA SET)

 

CAMERA ID

OFF

V-SYNC

INT

COLOR/BW

COLOR...

MOTION DET

 

ON...

ZOOM SPEED

 

3

DIGITAL ZOOM

OFF

DISPLAY ZOOM

OFF

DISPLAY P/T

OFF

EXIT

QUIT

Press [Enter]

(MOTION DET)

AREAUSER...

SENSITIVITY L ------ H RET

3-6

3-7

Image 16
Contents SCC-C6403 Important Safety Instructions FCC Statement Before Usage Chapter Locations of Control Adapter Connection Initial Setting Camera Address SetupBefore Installing Preparing the Cables Indoor Housing SHG-120 Outdoor Housing SHG-220Ceiling Mount Bracket SBR-100DCM Wall Mount Adaptor SADT-100WMCeiling Mount Adaptor SADT-100CM Pole Mount Adaptor SADT-100PMSetup Menu Overv iew Structure of the Setup Menu Sync Camera SET MenuCamera ID COLOR/BW Motion DETDigital Zoom Zoom SpeedDisplay Zoom Display P/TVideo SET Menu ExitIris ALCShutter AGCMotion FlickerlessWhite BAL DISPreset Focus ModeSpecial LevelZone SET Zone Enable Zone AreaLocation Zone ID SETAuto SET Auto PANSpeed Dwell TimeAuto Play Auto ReturnScan Play NumberAlarm SET Other SETSystem Info Short Keys Function KeyProduct specifications