Kenwood XD-A900 Operation of remote control unit, FM10 0/ a M 1 FM 5 0/ a M, Loading batteries

Page 16

16Operation of remote control unit

XD-951/A900/A700 (En)

Loading batteries

1 Remove the cover.

2 Insert batteries.

3 Close the cover.

ÖInsert two R6 (“AA”-size) batteries following the polarity indications.

Preparation section

Operation

Plug the power cord into the mains power outlet and press

the on/standby ( POWER) key of the remote control unit to turn power ON. After the power has been turned ON, press the desired key.

To turn power off, press the on/standby ( POWER) key again. The system enters the standby mode in which only the time display is lit.

ÖWhen pressing more than one remote control keys successively, press the keys securely by leaving an interval of 1 second or more between keys.

Remote sensor
6m
30˚	30˚

Operating range (approx.)

	1. The provided batteries are intended for use in operation checking, and their service life may be short.
Notes	2. When the remote controllable distance becomes short, replace both of the batteries with new ones.
Notes	3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction may occur.
	In such a case, change the installation position to avoid malfunction.

Application section

Knowledge sections

CHANNEL SPACE setting

(Except for the U.S.A., Canada, U.K., Europe, Russia and Australia)

The space between radio channels has been set to the one that pre- vails in the area to which the system is shipped. However, if the current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of AM/FM (MW/FM) broadcasts cannot be expected. In this case, change the channel space setting in accordance with your area by referring to the following table.

		Area	CHANNEL
			SPACE freq.


	1	U.S.A., Canada and South	FM : 100 kHz
		American countries	AM :	10 kHz


	2	Other countries	FM :	50 kHz
			AM :	9 kHz

1Turn power off.

ON/STANDBY

2Select the channel space.

Each press switches the space frequency alternately.

1 “FM100/AM10 kHz”

STEP,

2“FM 50 /AM 9 kHz” ....... STEP,

ÖThe “AM” display is variable depending on the model (country or area), and “MW” may be displayed in some areas.

FM10 0/ A M 1 0

FM 5 0/ A M 9

3Establish the selection.

ENTER

Image 16

Contents XD-951 XD-A900 XD-A700 Before applying power Safety precautionsMarking of products using lasers Except for some areas Class Laser ProductContents Basic sectionApplication section Knowledge sectionSpecial features DemonstrationDisc handling precautions CD accessoriesHandling of discs and tapes Discs which can be played with this unitConnection of the System Accessories System connection XD-951/XD-A900Canada Speaker Unit Before connecting the Front SpeakersFM indoor antenna System connection XD-A700 Main Unit Power cordSpeaker right Speaker left Application section KnowledgeRecommended speaker installation How to use the speaker stabilizer cushionsSpeaker Unit Main Unit Dolby Pro LogicConnection of Options Optional Parts FM outdoor antennaDigital OUT jack Optical Video deck Monitor TVPower For U.S.A. and Canada Controls and indicatorsMain Unit Cassette deck unit CD player unit1ON/STANDBY @DISPLAYDisplay Remote control Unit #ON/STANDBYOperation of remote control unit Channel Space settingFM10 0/ a M 1 FM 5 0/ a M Loading batteriesReception mode switching of FM broadcast CD PGM Dubbing Sound Display Timer Listen Mode ModeFor Russia Pola R Pilo TSwitching the power on OFF Volume adjustment18 Let’s put out some sound Basic use methodVO L 5 SUB LE V E LCD 0 1 1 2 CD 0 1 0 0Playback of CD Load a discStart playback Time display on the CD playerPlayback from desired track Skipping tracksTo pause playback Load a cassette tape Playback of tapeSelect the deck to be used for playback Start playback Tape B 0 0 0 TapeTape B 0 Relay play Tip for use of the tape counterSearching for the desired music program Dpss 7 3 ÁSelect the broadcast band Select a stationCollective presetting of stations auto preset One-by-one presetting manual presetSelect the tuning mode M 8 9 O28 Let’s record Load a tape in deck BSelect the tape transport direction 0 0Selection of the reverse mode Select the source to be recordedCD 0 Start recordingPoints in CD recording Copying tape Tape dubbing DI RTo stop dubbing Playback of CD Listening in the desired sequence program playbackP01 DI s C P01 TN O OP12 CL E a R PGM0 CD 0P01 D2 T 0 P12 D3 T ORepeated playback To repeat a discTo repeat all discs DIsC R E P E aTo repeat only one track Repe AT a C KTo repeat only the programmed tracks PGM RE P E a TConfirm that the PGM..... indicator is not lit Select the Random modeTo cancel random playback Listening to an unexpected title sequence random playbackTo switch the display contents S. Radio Data System For U.K., Europe and RussiaBBC 01 F M1 0 2 5Select the PTY search mode To select using the P.CALL 4 ¢ keysBTo select using the numeric keys 2Select the desired program typePress the key again during search to cancel it When a station is receivedStart the search To change to a different program typeAuto preset the stations M1 0 2 5Select the desired information Receive an RDS stationTP Traffic Program indicator Wait for the desired informationConvenient CD recording Selection of the convenient CD recording typeRecording of an entire CD Recording the programmed titlesRecording only desired titles CD ONE Track Record CD O NERecording of an entire CD CD Record DIsCPress the Dubbing key Select the discPress the Dubbing key 2Select CD Edit and press the SET key 3Select a disc and press the SET key5Start edit recording CD Record CD EditCD P GM RE C Program the desired tracksStart recording 1Select tracks in the order you want to play themAdjustment of balance and input level Effective Sound AdjustmentBA L a N C Selecting an equalizer pattern Leve L + Creation and memorizing of an equalizer patternEnte a To cancel SRS 3D Enjoying Sound Field EffectsSRs 3D O N SRs LE V E L Leve L +Delay time Dolby PRO Logic surround adjustmentSet the Dolby PRO Logic mode TEsT L OLB Y P R ONorm AL ELA Y1 5 m sDolby 3 Stereo adjustment Dolby 3 Stereo playORM AL Test LDSP Digital Signal Processor playback Set the DSP modeDIsC O SELE CT M O DTo decrease To increase Microphone Volume Connect a microphonePlay the music Sing along with the accompaniment Turn the MIC VOL. control fully CounterclockwiseAM 8 0 Clock adjustmentAM 8 4 Timer operation Sleep timer SleepAdjust the listening volume 7 OMake preparations for the play recording Enter the on time8 O Enter the OFF timeMake the desired reservation On nextWhen timer operation is not required To set the same timer program againPROG. ON/OFF Prog Auto Power Save Prog O N / OMaintenance Maintenance of the set Regardto contact cleanerMemory backup function ReferenceOperation to reset Remote control unitSymptom Cause Remedy Case of difficultyGeneral Cassette deckCD player Specifications XD-951/XD-A900 Surround speaker system CRS-N851Specifications XD-A700 Surround speaker system CRS-N551330 mm 315 mm 12-3/8 Weight net 260 mm 10-1/4 135 mm 180 mm Weight net180 mm, cone type 220 mm 8-11/16For your records