Dynaudio BM9S owner manual Switching the subwoofer on/off Power ON/OFF, Connecting loudspeakers

Page 10

Operation

LFE

Stereo

Connecting loudspeakers

If your source provides bass management, you can use the BM9S LFE input alone in LFE or SLAVE mode, depending on the management system capabilities. Avoid double processing if possible.

Connecting speakers

1.Connect the subwoofer as explained in “Connecting a single subwoofer” on page 7.

2.From the Subwoofer SAT/SUB OUT connect a XLR cable to the inputs of the power amplifier you use for your speakers.

Note:

The signals connected to the inputs are provided at the Slave OUT for connecting another subwoofer. See page 7 to learn more about connecting multiple subwoofers.

To power amplifier or active speakers

Switching the subwoofer on/off (POWER ON/OFF)

Once you have ensured yourself that all necessary connections have been made, the subwoofer and the connected components can be switched on.

XSwitch the subwoofer ON with the main POWER switch on the rear panel. The status LED on the rear of the subwoofer will light up red.

Automatic mode

After switching on the BM9S is in automatic mode:

When a music signal is detected, the internal amplifier is activated automatically.

The status LED on the back of the subwoofer will light up green.

As long as a music signal is available on the subwoofer’s input, it will remain switched on.

After 15 to 20 minutes of not sensing any input music signal, the subwoofer will switch itself to Standby mode automatically.

The status LED on the back of the subwoofer will light up red

Note:

XTo switch the subwoofer completely off, set the main POWER switch to the OFF position.

8

Dynaudio Acoustics BM9S

Image 10
Contents BM9S Contents InhaltImportant Safety Instructions Operating GuideSignal words Safety signsRisk of Electric Shock Do not Open About this operating manual Used signs and symbolsHow this operating manual is structured Unpacking GrilleControls and connections Damage of Device DUE to Improper Connection Connecting the subwooferSubwoofer inputs LFE/Slave➋ Connecting as subwoofer for satellites Connecting a single subwoofer➊ Connecting as LFE channel Connecting multiple subwoofersAutomatic mode Switching the subwoofer on/off Power ON/OFFConnecting loudspeakers Connecting speakersHigh Sound Levels Adjusting the volume GainSelecting the subwoofer cut-off frequency SUB Lowpass Selecting the cut-off frequencyFinding the correct phase setting Setting the phase PhaseSetting the satellite cut-off frequency SAT Highpass Setting the cut-off frequencyTroubleshooting Check this firstRisk of Fire Changing the fuseChanging the fuse Technical Specifications Parameter DataWarranty Sicherheitshinweise ServiceBestimmungsgemäßer Gebrauch Verwendete Zeichen und Symbole Zu dieser AnleitungZum Aufbau dieser Anleitung AuspackenStoffabdeckung ➏ ➒ SAT/SUB OUT ➏ ModeAnschluss- und Bedienelemente Pinbelegung ➐, ➑, ➒ 1 =Subwoofer anschließen Subwoofer Eingänge➊ Subwoofer als LFE-Kanal anschließen Einen einzelnen Subwoofer anschließenMehrere Subwoofer anschließen ➋ Subwoofer für Satelliten anschließenAutomatischer Modus Ein-/Ausschalten Power ON/OFFLautsprecher anschließen Lautsprecher anschließenSchädigung DES Gehörs Durch ZU Hohe Schallpegel Lautstärke einstellen GainSubwoofer-Grenzfrequenz wählen SUB Lowpass Lauter/leiser stellenSatelliten-Grenzfrequenz anpassen SAT Highpass Phase einstellen PhaseDie richtige Phasen-Einstellung finden Satelliten-Grenzfrequenz anpassenFehlersuche Prüfen Sie zuerst folgende PunkteFeuergefahr Durch Falsche Sicherung Sicherung ersetzenSicherung wechseln Technische Daten Parameter DatenGarantie Dynaudio Acoustics