Dynaudio BM9S owner manual Unpacking, Grille

Page 6

Before operation

1

2

3

Unpacking

Unpacking the subwoofer

1.Unpack the subwoofer on a clean, even and soft area; floor carpeting is very suitable.

2.The packaging should be opened from the top. Remove all accessories that come packed with the subwoofer (such as AC power cord and grille). Do not remove the top part of the protective material.

3.With the protective material still in place but with accessories removed, carefully tilt the packaging on its side and tilt again to turn it upside-down. Ensure that no part of the top-cover is obstructing the opening at the top.

4.The outer packaging can now be lifted away from the subwoofer itself. Remove the protective material that now is on top.

5.Open the bag and remove such from around the base of the subwoofer.

6.Again, carefully tilt the subwoofer on its side and again to turn it onto its feet. Note that the top part of the protective material will now come off easily so ensure that the subwoofer doesn’t drop or slide away in the process.

Check that the contents are complete:

Subwoofer: The factory-set power requirements (refer to label on rear of subwoofer) should correspond for the region where the subwoofer was purchased. Refer also to chapter “Important Safety Instructions” on page 1.

Front baffle grille.

AC mains lead. The supplied lead should be suitable for the region where the subwoofer was purchased.

Owners Manual.

Grille

The subwoofer can be operated without the grille. However, it is recommended that the grille is mounted during normal use to help prevent accidental damage or dirt settling on the cone of the loudspeaker. With subwoofers, the influence of the grille on the sound is virtually negligible.

To remove the grille:

XGently pull the grille at all corners.

To fit the grille:

XLine up the studs with the corresponding front baffle holes.

XGently push the grille in at all corners.

Note:

Be careful when mounting the grille not to touch the cone of the loudspeaker itself.

4

Dynaudio Acoustics BM9S

Image 6
Contents BM9S Contents InhaltImportant Safety Instructions Operating GuideSafety signs Signal wordsRisk of Electric Shock Do not Open Used signs and symbols About this operating manualHow this operating manual is structured Unpacking GrilleControls and connections Damage of Device DUE to Improper Connection Connecting the subwooferSubwoofer inputs LFE/Slave➋ Connecting as subwoofer for satellites Connecting a single subwoofer➊ Connecting as LFE channel Connecting multiple subwoofersAutomatic mode Switching the subwoofer on/off Power ON/OFFConnecting loudspeakers Connecting speakersHigh Sound Levels Adjusting the volume GainSelecting the subwoofer cut-off frequency SUB Lowpass Selecting the cut-off frequencyFinding the correct phase setting Setting the phase PhaseSetting the satellite cut-off frequency SAT Highpass Setting the cut-off frequencyTroubleshooting Check this firstChanging the fuse Risk of FireChanging the fuse Technical Specifications Parameter DataWarranty Service SicherheitshinweiseBestimmungsgemäßer Gebrauch Verwendete Zeichen und Symbole Zu dieser AnleitungAuspacken Zum Aufbau dieser AnleitungStoffabdeckung ➏ ➒ SAT/SUB OUT ➏ ModeAnschluss- und Bedienelemente Pinbelegung ➐, ➑, ➒ 1 =Subwoofer anschließen Subwoofer Eingänge➊ Subwoofer als LFE-Kanal anschließen Einen einzelnen Subwoofer anschließenMehrere Subwoofer anschließen ➋ Subwoofer für Satelliten anschließenAutomatischer Modus Ein-/Ausschalten Power ON/OFFLautsprecher anschließen Lautsprecher anschließenSchädigung DES Gehörs Durch ZU Hohe Schallpegel Lautstärke einstellen GainSubwoofer-Grenzfrequenz wählen SUB Lowpass Lauter/leiser stellenSatelliten-Grenzfrequenz anpassen SAT Highpass Phase einstellen PhaseDie richtige Phasen-Einstellung finden Satelliten-Grenzfrequenz anpassenFehlersuche Prüfen Sie zuerst folgende PunkteSicherung ersetzen Feuergefahr Durch Falsche SicherungSicherung wechseln Technische Daten Parameter DatenGarantie Dynaudio Acoustics