Classe Audio Explore High-Performance Audio Solutions with Classe CA-D200 Amplifier

Page 25

Specifications

n

Frequency response

10Hz – 20kHz, -1dB into 4Ω

n

Output power

200W rms into 8Ω

 

Harmonic distortion

400W rms into 4Ω

n

<0.018% @ 1kHz Balanced Input

n

Peak Output Voltage

116Vpeaktopeak,58Vrmsnoload

 

Input impedance

116V peak to peak, 58V rms into 8Ω

n

100kΩ Balanced / 50kΩ SE

n

Voltage gain

 

 

29 dB

n

Input level at clipping

1.4Vrms Balanced/SE

n

Intermodulation distortion

>80 dB below fundamental

 

Signal-to-Noise Ratio

into 8Ω Balanced

n

-100 dB at peak output into 8Ω (AES17)

n

Standby power consumption

 

<1W @ 230V

n

Rated power consumption

177W @ 1/8th power into 4Ω

n

Mains voltage

90V - 264V, 50/60Hz

n

Overall Dimensions

Width: 17.50” (445mm)

 

Depth (excluding connectors): 16.50” (419mm)

 

Net weight

Height: 4.78” (121mm)

n

28.0

lbs

(12.70

kg)

n

Shipping weight

37.0

lbs

(16.30

kg)

All tests un-weighted and 20Hz – 20kHz measurement bandwidth used.

For more information, see your Classé dealer, or contact:

B&W Group Ltd.

5070 François Cusson

Lachine, Quebec

Canada H8T 1B3

Telephone

+1 (514) 636-6384

FAX

+1 (514) 636-1428

Internet:

http://www.classeaudio.com

email:

cservice@classeaudio.com

Classé and the Classé logo are trademarks of B&W Group Ltd., Worthing U.K. All rights reserved.

AMX® is a registered trademark of AMX Corporation of Richardson, TX. All rights reserved. Crestron™ is a trademark of Crestron Electronics, Inc. of Rockleigh, NJ. All rights reserved. Control 4™ is a trademark of Control 4 Corporation of Saltlake City UT. All rights reserved.

25

Image 25
Contents CA-D200 Two-Channel Amplifier Class Important Safety Instructions Contents Welcome to the Classé family Word about installationUnpacking and Placement Warm up/break-in period Please read this manual… Special Design Features Front Panel Standby button & LED status indicatorOn red Flashing blueBalanced XLR Input Rear PanelSpeaker Outputs Single-Ended RCA InputClassé CAN-Bus Control Ports IR Input and OutputRS 232 Control Port DC Trigger Input and OutputRJ-45 RJ-45 DB9 female adaptorUSB Port AC Mains InputConfigure your amplifier turn-on delay/amp number InstallationMake your preamp/processor connections Make your speaker connections CAN-BusDouble-check all your connections CAN-Bus will allow a Classé touchscreen toCategory 5 Network Cables Classé CAN-Bus Equipped ProductsCAN-Bus equipped components in your system CAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface BoxFor any system with SSP-300 or SSP-600 Any combination of models in any orderFollowing CAN-Bus features are shared by all models CAN-Bus shared featuresPlayLink Following CAN-Bus features are model specificAmp info Event log Care and Maintenance No sound, and Standby LED is not lit TroubleshootingNo sound, and Standby LED is blinking red Protection circuitry has been engagedMains voltage 100-120VAC Fuse type AC mains fuse is blownRating 3AH Mains voltage 200-240VAC Fuse type Rating 15AHSpecifications CA-D200 DimensionsPage +1 514 +1 514 636-1428 fax François Cusson Lachine, QuebecNorth America 514