Orion Car Audio XTR52, XTR62 owner manual Installing the Crossover, Tweeter Level Controls

Page 7

Step 5: Install tweeter in flush mount housing.

Step 6: Connect the speaker wires observing the correct polarity.

Step 7: Install tweeter and housing in the hole cut for mounting, so that the trim ring is flat with the front of the surface.

Step 8: Use the supplied X bracket & screw to secure the housing to the surface.

Flush Mount

Tweeter

X Bracket

Tweeter Assembly

Cup

 

 

Screw

 

Figure 5

 

 

 

Wiring

Figura 5

Flush Mount

Tweeter

 

 

Harness

Abbildung 5

Trim Ring

Wire

Panel

 

INSTALLING THE CROSSOVER

Step 1: Find a location for the crossover away from any factory or after market electrical wires. It is recommended to mount the passive crossover close to the amplifier.

Step 2: Mount the crossover using the supplied screws.

Step 3: Connect the wires. Make sure the speaker wires for the midrange go to the mid/ woofer output and the tweeter to the tweeter output. Be sure to observe the correct polarity. Changing the polarity of the tweeter may be necessary for optimum sound quality.

TWEETER LEVEL CONTROLS

The three position switch in the crossover box labeled “TW Level” adjusts the relative volume of the tweeter with respect to the midrange. The 0db position is referenced as equal output from the midrange and the tweeter. The -3dB and +3dB positions offer -3dB less and +3dB more output from the tweeter respectively. Tweeter level can be adjusted independently for right and left channels to compensate for different listening tastes and mounting locations.

6

© 2008 directed electronics—all rights reserved

Image 7
Contents Component Speaker Introduction Table of ContentsPractice Safe Sound Finding Speaker Mounting Locations InstallationWHAT’S in the BOX Tools of the TradeRear Deck Mounting Door MountingInstalling the MID/WOOFERS Surface Mounting Installing the TweeterFull Flush Mounting Tweeter Level Controls Installing the CrossoverWiring Diagram Features SpecificationsXTR52 XTR62 Montage SUR UNE Portière Installation DES HAUT-PARLEURS Médiaux ET DE GravesFrançais OÙ Monter LES HAUT-PARLEURSMontage EN Surface Installation DU HAUT-PARLEUR DaigusMontage Encastré Caractéristiques Installation DU RépartiteurRéglage DU Niveau DE HAUT-PARLEURS D’AIGUS SpécificationsMontaje EN LA Repisa Trasera EspañolUbicaciones DE Montaje DE LOS Altavoces Montaje EN LA PuertaMontaje EN Superficie Instalación DEL TweeterMontaje AL RAS Características Instalación DEL CrossoverControles DE Nivel DE Tweeter EspecificacionesDirected electronics-Reservados todos los derechos Einbau IM Kofferraum DeutschSO Platzieren SIE DIE Lautsprecher TüreinbauOberflächeneinbau Einbau DES HochtönersBündiger Einbau Eigenschaften Installation DER CROSSOVER-EINHEITHOCHTÖNER-PEGELREGELUNG DatenDirected electronics-Alle Rechte vorbehalten Montaggio NEL Piano Portaoggetti Posteriore Installazione DEI MIDRANGE/WOOFERItaliano Montaggio Sulle PortiereMontaggio a Superficie Installazione DEL TweeterMontaggio a Filo Caratteristiche Installazione DEL CrossoverComandi DEL Livello DEL Tweeter Dati TecniciDirected electronics-tutti i diritti riservati Instalação no Painel Traseiro PortuguêsDeterminação DOS Locais Para Instalação DOS ALTOS-FALANTES Instalação NAS PortasInstalação NA Superfície Instalação do TweeterInstalação Embutida Instalação do Crossover Controles DE Volume do TweeterEspecificações Directed electronics-Todos os direitos reservados Warranty