Technics SL-P9066, SL-PD967 Troubleshooting guide, Product information, Problem Probable Causes

Page 19

Troubleshooting guide

Before requesting service for this unit, check the chart below for

a possible cause of the problem you are experiencing. Some sim-

ple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.

If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to

the directory of authorized service centers (enclosed with this unit) to locate a convenient service center, or consult your Technics dealer for instructions.

(In U.S.A. consult MSC Authorized Servicenters for detailed in- structions.)

I

Problem

 

Probable

cause(s)

Changer

will not play.

A disc(s)

or other foreign

object(s) has fallen

 

 

inside the

changer.

 

 

 

Moisture

has collected

in the changer.

Suggested remedy

I

• Open the loading drawer, and then remove the

object.

Switch on and allow the changer to dry out for about

one hour before using it.

The disc in the changer does not play.

Play stops before changing to the next disc.

The disc is upside down.

The disc is dirty.

The disc is scratched. ]-he disc is warped.

The disc is not within specified standards. The loading drawer is open.

• Make sure the label is facing upward.

• Wipe the disc with a soft cloth.

• Replace the disc with a new one.

• Press the OPENtCLOSE button to close the loading

drawer.

• Wipe the disc with a soft cloth.

A certain music passage can't be played correctly.

These is noise from the tuner or disturbance on the

TV screen.

When program play is started, an error message (-E) appears on the display.

An error message (- E) appears on the display, and the changer stops operating.

The loading drawer stops in the middle o! opening.

The disc is dirty.

The disc is scratched.

Caused by high-frequency signals from this

changer.

Play was started without a track being programmed.

The mechanism of the changer has been improperly adjusted.

• Replace the disc with a new one.

• Use the changer further away from the tuner or TV.

• If the tuner or TV'santenna is the indoor type, use an

outdoor

one.

• Program

a track.

• Turn the unit off and then back on again.

However, if the loading drawer is fully open, take out

the compact disc(s) at the front position and then turn

the unit off and then back on again.

Product service

Do not attempt to remove the cover(s) or repair the unit

yourself.

Refer servicing to qualified personnel only.

Product information

For product service, product information or assistance in pro- duct operation, refer to the servicenter directory.

19

Image 19
Contents Technics Contents FCC Service Installation En vironm en t137Random Mode button Power Standby /ON switchPitch Control buttonlindicator Time mode button Time ModeSJP2249 ConnectionsStereo connection Cable Press Desired Disc But Ton 1 POWEn Press PowerOPEN/CLOSEPress OPEN/CLOSE to open Io EPress oPENicLOsE againEPress the numeric buttons to Select the track To stop playPress 0to specify Track Number To cancel program modePress Program Mode twice Press NumericPress Recall Press Random Mode so thatRND indicator illuminates To cancel random play modeJr 1 2 .otO specify the track number To cancel delete modePress Program Mode Press the disc button 1Spiral play Using the remote controlTo cancel spiral play mode SPIRALPress Spiral again Press SpiralI Press and hold 11 or When the desired track has been foundSequential play mode Idscan Press ID ScanDisc SKIPPress Disc Skip to rotate the disc % tray To skip tracksJ-i During operation of the edit guide function To cancel repeat mode REPEATPress Repeat againProgram play mode Programldeletelrandomlspiral modeEDITGUIDEPress Edit Guide to select Tape Length Edit guideDiscskip Press Disc Skip to select Disc to be recorded Prepare the tape deck for recordingTo play in 0% standard pitch Turn the knob in the ..... or+ direction To fine-tune the pitchAurocuE Press Auto CUE Handling precautionsTo cancel auto cue mode Auto CUE Press Auto CUE Storage preca u tionsSuggested remedy Troubleshooting guideProblem Probable Causes Product informationPress OPEN/CLOSE to open the loading drawer Preparations for moving the unitMatsushlta Electric of Canada Limited