Sanyo DV-S100 manual Wiring, Basic connection, Interference on 88.9 MHz, Replacing the fuses

Page 39

Wiring (1)

Basic connection 1

The car stereo should be with FM tuner.

Tune the radio to the frequency to which the installer has set the FM modulator. (FM 88.9 MHz or FM 88.3 MHz)

Monitor with Video input jack

Monitor with Video input jack

If not long enough, use the extension cable included.

Yellow	To video input	To video input
(Front)	(Yellow)	To video input
		(Yellow)

Yellow

(Rear)

* You can add a monitor for rear seats.

R

Red

Not used.

White

L

Changer unit

Interference on 88.9 MHz

¡If a clear signal cannot be obtained on 88.9 MHz, change the position of the frequency select switch on the back of the FM

Modulator and tune the radio to 88.3 MHzDriver when using the changer.

¡Select a frequency before mounting the FM	88.9	88.3

Modulator.

Radio sensitivity is slightly reduced when the

FM Modulator is connected.

Replacing the fuses

If a fuse becomes blown, open the fuse holder as shown in the illustration and remove the fuse from both terminals.

WARNING

Bright green

Attached DIN cable (8 pin, 5 m)

Attached parking brake cable

Bright green

Attached Remote control sensor

	Attached FM						Antenna
	Attached FM						socket
	modulator						socket
										Car stereo
										Car stereo
										with FM

					Connect to car antenna.


			+12 volt Accessory/Switched (red)
			Connect to where the power is
			supplied when the ACC power or
			ignition switch is turned ON.
	Fuse 5A		+12 volt Constant (yellow)
	Fuse 5A		Connect this lead to the cable to
			Connect this lead to the cable to
			which power is continuously supplied
			and which has been passed through
			the car’s fuse unit.
			Ground (black)
			Screw this to a metal part of the
			car.

Connect to car’s parking brake line.

Be sure to replace with a fuse with the correct rated capacity (5 A). If a fuse with a capacity greater than the rating is used, fire may result.

(Check the lead wire connections once more before replacing the fuses.)

38

Image 39

Contents DV-S100 Dolby Digital IntroductionFunction available with a video CD MacrovisionContents With new discs Precautions for handling discs How to use the magazineInstalling the magazine Loading a discInstallation parts for Changer unit AccessoriesFor safe driving For safe and efficient operationPlayable discs When the changer is connected directly to Sanyo CD or Before using the system Power OnSetting up for operation Power On and PlayAudio CD Operation Screen Remote controlHow to load the batteries Range of remote control operationName & functions of each part To Stop Play Switching OffPausing Freezing Stopping PlayDuring play, press a skip button or Selecting a DiscAdvancing / Returning to a Chapter or Track Press a disc select button orAudio CD Using the Title MenuFast Playback DVD and Video CDUsing PBC Playback Using DVD MenusZSee step Stopping PBC Playback and Beginning Normal Play Stopping PBC Playback and Beginning Normal PlayFunction operates. zSee To Stop Play At the upper right of the screen appearsUsing Frame Advance Play and Slow Play Using Frame Advance PlayUsing Slow Play Press the enter button During play, press the search buttonWhile play information is displayed, use the search button Time of title, track number, elapsed time of trackSwitching the Audio Language Switching the Audio Output MethodVideo CD Switching the Angle Switching the Subtitle LanguageProgram list creation screen appears ZSee Using Scan Play, Random Play, and Program Play on thisCreating a Program List ZSee Creating a Program List on thisLights ZSee page 8, Audio CD Operation Screen Indicator on the operation screenPress Input number display shows Press Input number display shows 2 next toUsing Repeat Play Video CD, Audio CDDuring play, press the repeat button Using A-B Repeat Play Mode Displaying a Disc List Press the A-B repeat buttonPress the list button Press the enter button . The selected disc is played Displaying a Disc List Displaying Running TimePress the list button or the return button Press the time buttonPress the time button during play or while paused Switching the Type of Running Time DisplayPress the stop button To stop play Press the setup button Change the settingsPress the play button . Play begins DVD menu language setup screen is displayedChanging the DVD Menu Language Press the return button or the left cursor buttonAudio language setup screen is displayed Changing the Audio LanguageYou can change the DVD audio language Subtitle language setup screen is displayed Changing the Subtitle LanguageSubtitle Language and press the enter button Enter button Subtitle language or Off when hiding subtitles and pressChanging the Digital Output Use the up/down cursor buttons , to select a preferredPan & Scan Use the up/down cursor buttons , to select the audioOutput LPCM/Bitstream and press the enter button Letter BoxChanging Parental Settings When using this unit for the first timePassword registration screen is displayed Number Press the enter button Password re-entry screen is displayedUse the number buttons to enter the registered PasswordChanging the parental level Use the up/down cursor buttons , to select a levelChanging the password OSD Message setup screen is displayed Switching Between OSD Message Display and Non-DisplayChanging the Player Language Player Language setup screen is displayedPosition of the built-in anti-vibration boards Before wiring and installationInstallation and Wiring Precautions Transport Lock ScrewsReplacing the fuses WiringBasic connection Interference on 88.9 MHzOther connection Example When your car stereo has RCA line-in terminalsProcedure for installation on carpet Horizontal position InstallationBuilt-in anti-vibration Installation of FM modulator Message displays TroubleshootingFast forward, fast reverse, frame ¡FM modulator SpecificationsDimensions W x H x D Approx x 26 x 45 mm Weight Approx g ¡ChangerPage 2RR6P10A06700