Sharp PN-S655 manual Nsetup, Menu Items NOPTION

Page 7

nSETUP

OSD H-POSITION

Adjusts the horizontal display position of menu screen.

OSD V-POSITION

Adjusts the vertical display position of menu screen.

LANGUAGE

Sets the display language for the menu screen.

HDMI AUTO VIEW

When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV2 input terminal.

PICTURE FLIP

A picture flips to appear.

STANDARD

 

MIRROR

ABC

 

ABC

 

 

 

UPSIDE DOWN

 

ROTATE

ABC

 

ABC

 

 

 

POWER ON DELAY

You can delay the screen display after the monitor is turned on. The period can be set up to 60 seconds in units of one second. When this function is activated, the power LED flashes (at approx. 1 second interval) in orange. This function is disabled when 0 is specified.

STANDBY MODE

When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode.

When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. Also, certain RS-232C commands cannot be used in standby mode. (See page 16.)

RS-232C/LAN SELECT

Selects the method with which to control the monitor from the computer.

RS-232C/LAN COMMAND

Set the return value for the RS-232C command. Normally, you do not need to change this setting from

NORMAL.

 

NORMAL

The end code of the return value is CR+LF.

MODE1

The end code of the return value is CR only.

MODE2

The length of the return value is fixed to 4

 

digits. The end code is CR only.

 

When the return value has 1 to 3 digits, the

 

empty digit(s) from the left is filled with a

 

one-byte space(s).

ID No. SET

Assigns ID numbers to monitors connected in a daisy chain (see page 13), using RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID number is set.

LAN SETUP

Configures the settings to control the monitor from the computer via LAN. (See page 21.)

Menu Items

nOPTION

DATE/TIME SETTING

Set the date and time. Press or to select the date

and time, and press or to change the numerical values.

Set the date in “Year/Month/Day” order.

Set the time on a 24-hour basis.

SCHEDULE (See page 9.)

You can set the time to switch the monitor on and off.

INPUT SELECT

 

DVI SELECT

Selects the input mode to be used.

BNC SELECT

Selects the input mode to be used.

HDMI SELECT....

Selects the input mode to be used.

HDMI AUDIO SELECT...

Selects a terminal to which audio signals

 

are input in PC2/AV2 mode.

QUICK SHOOT

 

Reduces the visual lag inherent in fast-motion scenes.

AUDIO OUTPUT

Sets the volume of sound output from the PC/AV audio

output terminals.

 

VARIABLE

You can adjust the volume using VOLUME.

FIXED

Fixes the sounds.

INPUT SIGNAL (PC3/PC4)

If a computer connected to the PC3/PC4 input terminal outputs any of the following resolutions, make a selection from the following options.

480 LINES

AUTO, 640x480 or 848x480

768 LINES

AUTO, 1024x768, 1280x768, or 1360x768

1050 LINES

1400x1050 or 1680x1050

SCAN MODE (AV input)

Sets the scan mode used for AV mode input.

MODE1

Over-scan display

MODE2

Under-scan display

MODE3

Under-scan display when the input signal

 

is 1080i/p. Otherwise, over-scan display

*Even when MODE1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot.

SELF ADJUST

On a PC3/PC4 screen, specify whether to perform screen adjustment automatically or not. When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input signals changes.

“ADJUSTING” appears on the screen during the adjustment.

POWER MANAGEMENT

POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode when the PC screen is displayed.

AUTO INPUT CHANGE

Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present.

When video signals exist in multiple input modes, the switching priority is as follows:

PC1, PC2, PC3, PC4, AV1, AV2, AV3, AV4 and AV5. (Input mode switching may take 15 seconds or more, depending on the connected equipment. Input signals may not be detected properly and a priority may change, depending on the connected equipment or video signals.)

7 E

Image 7
Contents PN-S655 Contents Display Basic OperationMute MenuCut off Basic Operation NSwitching the screen sizeWide Zoom Normal Dot by DotNMenu screen display Menu ItemsDisplaying the menu screen NExample of operationNPICTURE Menu item detailsMenu Items NSCREENMenu Items NOPTION NSETUPNPIP/PbyP NENLARGE PC inputNDual screen display Menu Items NSCHEDULE NEnlargeNADVANCED items AV input See Adjustments for PC screen displayNAutomatic adjustment NScreen display for adjustment11 E Communication conditions Communication procedureControlling the Monitor with a PC RS-232C PC connectionNResponse code format 13 ENID numbers OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ← 002VOLM0030 VOLM0020 ←Controlling the Monitor with a PC RS-232C NRepeater control NRepeater control commandVolume settings for all monitors are returned 15 EControlling the Monitor with a PC RS-232C RS-232C command tablePower control/Input mode selection How to read the command tableControlling the Monitor with a PC RS-232C Picture menu 17 EAudio menu Option menu Controlling the Monitor with a PC RS-232C Setup menuPIP/PbyP menu Initialization/Functional Restriction Setting Function menuImage Position Epos setting 19 EControlling the Monitor with a PC RS-232C Others Temperature Sensor DstaTo set on the monitor Settings to connect to a LANControlling the Monitor with a PC LAN 21 EDefault Gateway 0.0 This monitor is factory preset as shown below IP AddressControlling the Monitor with a PC LAN To set from a PC Basic operation 23 EControlling with a PC Controlling the Monitor with a PC LANControl Information Adjustment25 E Network LAN SetupNetwork Security Mail Originator Network GeneralMail Recipient 27 EMail Periodical URL Information Service & Support URL InformationSpecify the condition to display the URL 29 E PN-S655 G EN08F1
Related manuals
Manual 30 pages 27.1 Kb