Sharp PN-U553, PN-U473 Controlling the Monitor with a PC LAN To set from a PC, Set up process

Page 40

Controlling the Monitor with a PC (LAN)

■ To set from a PC

When the monitor is connected to a PC, LAN settings can be configured via PC.

Set up process

(1)Connect your monitor to a PC

(2)Specify the PC’s IP address

(3)Configure the monitor’s LAN settings

(1) Connecting your monitor to a PC

Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor.

LAN terminal

 

 

 

 

PC

 

 

To LAN terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LAN cable

(commercially available, crossover)

(2) Specifying the PC’s IP address

To configure the monitor’s LAN settings, you must temporarily change the settings on the PC.

This explanation is based on Windows 7.

1.Log on to the PC with an administrator account.

2.Click [Start], and then click “Control Panel”.

3.Click “View network status and tasks” in “Network and Internet”.

In “Classic View”, click “Network and Sharing Center”.

4.Click “Local Area Connection” and then “Properties”.

5.Click “Internet Protocol Version 4 (TCP/IPv4)” and then “Properties”.

6.Make a note of the current IP address, subnet mask, and default gateway settings.

Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

7.Temporarily change the IP address and subnet mask.

To access the monitor as it is shipped from the factory, set as follows.

IP Address: 192.168.150.1

Subnet Mask: 255.255.255.0

Default Gateway: (leave blank)

8. Click [OK] and then reboot the PC.

TIPS

• This monitor is factory preset as shown below. (When DHCP CLIENT is set to OFF)

IP Address

: 192.168.150.2

Subnet Mask

: 255.255.255.0

Default Gateway

: 0.0.0.0

(3)Configuring the monitor’s LAN settings

Access the monitor using Internet Explorer.

Controlling the monitor

1.Turn the power ON to the monitor.

2.Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN.

3.Set DHCP CLIENT of LAN SETUP of COMMUNICATION SETTING on the SETUP menu to OFF.

PC operation

4.Launch Internet Explorer, in the “Address” box type “http://192.168.150.2/” and press the Enter key.

5.Leave the “Username” and “Password” boxes blank and click [Login].

E40

Image 40
Contents PN-U553 PN-U473 PN-U423 Information on Disposal for Users private households Information on Disposal for Business UsersEuropean Union Other Countries outside the EUFor Customers in U.K GREEN-AND-YELLOWBlue BrownDear Sharp Customer Safety Precautions Tips and Safety Instructions For the monitor in landscape orientation For the monitor in portrait orientationContents Supplied ComponentsRemote control sensor See Input switch See Power switch See Part NamesNFront view NRear view LCD panelSignal transmitter Part Names NRemote control unitReturn button See Size button See Connecting Peripheral Equipment 11 EConnecting Peripheral Equipment Connecting the Power Cord 13 EBinding Cables PN-U553 Cables connected to the terminals on the rearPreparing the Remote Control Unit Installing the batteriesRemote control operation range 15 ETurning Power On/Off Turning on the main powerTurning power on/off Status Status of the monitorNDate/time setting Turning Power On/Off NOperation mode17 E Basic Operation Basic Operation NSwitching the screen size 19 EWide Normal Dot by DotMenu Items Displaying the menu screenNMenu screen display NExample of operation21 E Menu item detailsMenu Items NSCREENMenu Items NPICTURE 23 E NSETUPMenu Items NAUDIO Menu Items NMONITOR NMULTI/PIP25 E Menu Items NOTHERSNEnlarge Menu Items NDual screen displayPIP NSCHEDULE 27 EInput Adjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment Opening the adjustment patternALL Reset Adjustment Lock29 E OSD DisplayControlling the Monitor with a PC RS-232C Communication procedure PC connectionCommunication conditions NResponse code format 31 ENID numbers Wait ← OK 002 ← VOLM0010 OK 001 ←33 E NRepeater control commandControlling the Monitor with a PC RS-232C NRepeater control RS-232C command table Power control/Input mode selectionHow to read the command table Controlling the Monitor with a PC RS-232CControlling the Monitor with a PC RS-232C Picture menu 35 EAudio menu Controlling the Monitor with a PC RS-232C Setup menu Monitor menuInitialization/Functional Restriction Setting Function menu 37 EControlling the Monitor with a PC RS-232C MULTI/PIP menu Others menuTemperature Sensor Dsta Controlling the Monitor with a PC RS-232C OthersSettings to connect to a LAN Controlling the Monitor with a PC LAN39 E To set on the monitorSet up process Controlling the Monitor with a PC LAN To set from a PC41 E Controlling with a PCControlling the Monitor with a PC LAN Basic operationSetup Controlling the Monitor with a PC LAN PC operationScreen Picture Audio43 E Advanced operation Command-based control Troubleshooting 45 ETroubleshooting Power LED is flashing in red and green alternatelyNProduct Specifications Specifications47 E Specifications NDimensional Drawings 49 E Specifications NPower managementNDDC plug and play Specifications NCompatible signal timing PC NCompatible signal timing AV51 E Specifications NDVI-D output terminal pins NRS-232C output terminal pins53 E PN-U553U473U423 Me EN13G1
Related manuals
Manual 2 pages 28.05 Kb Manual 28 pages 17.73 Kb

PN-U423, PN-U473, PN-U553 specifications

The Sharp PN-U473 is a sophisticated large-format display ideal for a variety of commercial environments, offering both stunning visuals and robust features. This 47-inch LCD panel is designed with versatility in mind, making it suitable for digital signage, presentations, and information displays across various sectors.

One of the standout features of the PN-U473 is its ultra-thin bezel, which enhances immersion when used in multi-screen configurations. This design element minimizes distractions, allowing viewers to focus on the content being displayed. The Full HD resolution of 1920 x 1080 ensures that images and text are crisp and clear, providing superior visual performance that is crucial for conveying important information.

The PN-U473 is equipped with advanced display technologies, including a high brightness level of up to 500 cd/m². This makes it particularly effective in high-ambient light environments, where visibility is often a concern. The display utilizes LED backlighting, which not only enhances brightness and contrast but also contributes to energy efficiency, helping businesses reduce operational costs.

Connectivity options are extensive, featuring multiple inputs including HDMI, DisplayPort, and VGA, which provide flexibility for various multimedia sources. The built-in USB media player further enhances its functionality, allowing users to display files directly without the need for a separate computer.

Additionally, the PN-U473 supports advanced image processing technologies that ensure smooth video playback and excellent color accuracy. This capability is essential for applications where detail and clarity are paramount, such as retail or corporate environments.

Moreover, the display is designed for 24/7 operation, making it a reliable choice for continuous use scenarios where downtime can be costly. Its robust thermal management system helps maintain optimal performance under prolonged use.

In conclusion, the Sharp PN-U473 combines cutting-edge display technology with practical features tailored for commercial applications. Its impressive visual quality, versatile connectivity, and durability make it a valuable asset for businesses looking to enhance communication and engagement through impactful visual presentations. Whether in retail, corporate settings, or public spaces, this display stands out as a reliable solution for effective messaging and information dissemination.