Sharp PN-465E operation manual How to Install the Monitor, Mounting precautions

Page 11

How to Install the Monitor

Mounting precautions

Since the monitor is heavy, consult your dealer before installation.

Installing or moving the monitor must be done by two or more people.

A stand and mounting bracket compliant with VESA specifications is required. Do not use any screw holes other than VESA holes for installation.

When moving the monitor, be sure to hold it with the handles both on the rear and the unit bottom. Do not hold the LCD panel. This may cause product damage, failure, or injury.

Install the monitor with the surface perpendicular to a level surface. If necessary, limit the tilt between 0 and 20 degrees downward.

Mounting the monitor on the wall requires special expertise and the work must be performed by an authorised SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility

for accidents or injuries caused by improper mounting or mishandling.

This monitor should be used at an ambient temperature between 0°C and 40°C. Provide enough space around the monitor to prevent heat from accumulating inside.

For the monitor in horizontal orientation

 

Unit: cm

 

20

 

*

5

5

 

5

For the monitor in vertical orientation

 

Unit: cm

 

20

 

*

5

5

 

5

*The monitor can be installed close to a wall, etc. However, the monitor emits heat during operation. Be aware that heat emitted from the monitor may discolour or alter the wall.

If it is difficult to provide such space because the monitor is installed inside a housing or for other reasons, take other measures to keep the ambient temperature between

0°C and 40°C such as installing a fan in the housing.

Adhere to the following when installing the monitor in the vertical orientation. Failing to adhere to the following may cause malfunctions.

-Install the monitor such that the power LED is located on the downside.

-Set the MONITOR on the SETUP menu to PORTRAIT. (See page 19.)

Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction.

After mounting, it is recommended to take some measures to prevent the monitor from falling down.

Do not place the monitor on a device which generates heat.

Be sure to use a stand or a wall-mount/ceiling-mount bracket designed or designated for mounting the monitor.

This monitor is designed to be installed on a concrete wall/ ceiling or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.

This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

Use the supplied vertical logo sticker when you install the monitor in vertical orientation.

*

INPUT

*Do not remove the factory-affixed sticker but affix the logo sticker over it. Be careful not to cover the remote control sensor or buttons.

ENGLISH

9E

Image 11
Contents PN-465E Sharp Electronics Europe GmbH GREEN-AND-YELLOW Earth Blue Neutral Brown Live Refer Servicing to Qualified Service PersonnelFor Customers in U.K Other Countries outside the EU Information on Disposal for Users private householdsInformation on Disposal for Business Users European UnionDear Sharp Customer Safety Precautions fluorescent tubes in this product have a limited lifetime Tips and Safety InstructionsContents Front view Supplied AccessoriesLCD panel Remote control sensor See Part NamesPart Names Rear view Remote control unitSignal transmitter Power button See Mute button SeeFor the monitor in vertical orientation How to Install the MonitorMounting precautions For the monitor in horizontal orientationAV1 input terminal AV2 input terminals Connecting Peripheral EquipmentConnection with AV equipment Connection with a PC11 E Connecting external speakersConnecting multiple monitors Connecting Peripheral EquipmentMonitor is heavy. It must be handled by 2 or more people Connecting the Power CordInto the AC input terminal. into the AC power outlet Mounting the Temporary StandsBinding Cables Preparing the Remote Control UnitSetting the batteries Remote control operation rangeDisabling power on/off operations Turning Power On/OffTurning on the main power Turning power on/offMenu Basic Operation15 E MuteDotbyDot Basic Operation Switching the screen sizeWide Zoom Normal Example of operation Menu Items17 E Displaying the menu screenMenu Items Menu item details19 E Dual screen display Menu Items ENLARGE PC inputPIP/PbyP Vertical orientation 21 EMenu Items Enlarge Horizontal orientationADVANCED items AV input See Automatic adjustment is complete in several seconds Adjustments for PC screen displayAutomatic adjustment Screen display for adjustmentRS-232C Adjustment LockOSD Display LEDPC connection Communication procedureControlling the Monitor with a PC 25 EID numbers Controlling the Monitor with a PC Response code formatCommunication interval Controlling the Monitor with a PC Commands for ID control27 E Controlling the Monitor with a PC Repeater control Repeater control commandVolume settings for all monitors are returned 29 E RS-232C command tablePower control/Input mode selection How to read the command tableAudio menu Setup menuControlling the Monitor with a PC Picture menu PIP/PbyP menu Enlarge menu When the input mode is PC31 E Controlling the Monitor with a PC Option menuOthers Temperature Sensor Dsta33 E TroubleshootingVesa DPMS, DVI Dmpm SpecificationsProduct Specifications Vesa DDC2BSpecifications Dimensional DrawingsCompatible signal timing PC 35 ERS-232C output terminal pins Specifications Power managementPC1/AV1 input terminal pins RS-232C input terminal pins