JBL CS5, CS3 manual Learning Codes from a Remote Control, Program Indicator, Erasing Learned Codes

Page 29

LEARNING CODES FROM A REMOTE CONTROL

The CS3/CS5 remote is able to “learn” codes from other remote controls that might be part of your system setup, like the one from your TV. To learn or transfer codes from an IR remote control to the AVR’s remote, follow these steps:

1. Place the front of the original remote with the code being sent so

that it is facing the IR Transmitter Window on the CS remote “head-to-head.” The remote controls should be between 2cm and 4cm apart.

2.Select the button on the remote that you wish to use as the device selector for the codes about to be entered. This must be any of the Input Selectors 0.

3.Press the Input Selector 0 button chosen and the Learn button at the same time. Hold these buttons until the Program

Indicator flashes amber and the light under the device selector button turns red. Release the buttons. It is important that you begin the next step within 20 seconds.

4.Press the button on the CS remote that you wish to program.

Note that the Program Indicator

will stop flashing.

IMPORTANT NOTE: Codes cannot be taught to all buttons on the

remote. In these cases the Program Indicator keeps flashing after the button was released.

5. As long as the Program Indicator is on steadily (for five sec- onds), press and hold the button on the original remote that you wish to “teach” into the CS remote. If you pressed the button too late or no command was received within five seconds, the

Program Indicator

will flash red three times and then amber,

then simply repeat Step 4. When the Program Indicator

turns

green, release the button on the original remote. Note that the

Program Indicator

will then begin to flash amber again.

 

NOTE: If the Program Indicator

turns red steadily during Step 5,

the programming was not successful. Repeat the steps to see

 

whether the code will “take.” If the indicator keeps flashing red in Step 5, this code cannot be taught.

6.Repeat Steps 4 though 5 for each button on the source remote that you wish to transfer to the CS remote.

7.Once all codes have been transferred from the original source

remote to the CS remote, press the Learn button. This will turn off all LEDs and turn off the learning mode.

8.Repeat Steps 1 through 7 for any additional remotes you wish to “teach” into the CS remote.

Erasing Learned Codes

The CS remote allows you to remove or erase the code learned into a single button for a single device, to remove or erase all the codes that have been learned for a single device, or to erase all commands that have been learned to all devices.

To erase a single learned code from within a single device’s set- tings, follow these steps:

1.Press and hold both the Input Selector 0 within which the individual button to be erased has been programmed and the

Learn button.

2.When the red LED under the Input Selector 0 turns red and the

Program Indicator flashes amber, release the buttons.

3.Press and release the Input Selector 0 again for the device within which the individual button to be erased has been programmed.

4.Press the 7 button three times.

5. Press and release the individual button for which the code is to be

erased. The Program Indicator will blink green two times and then return to amber.

6.To erase other buttons within the same device, press them as noted in Step 5.

7.When all buttons to be erased have been pressed, press the Learn button to complete the process.

To erase all codes within a single device, follow these steps:

1. Press and hold both the Input Selector 0 for which you wish to

erase the codes and the Learn

button.

2.When the red LED under the Input Selector 0 turns red and the

Program Indicator flashes amber, release the buttons.

3.Press and release the same Input Selector 0 again for the device whose codes you wish to erase.

4.

Press the 8 button

three times.

5.

The Program/SPL Indicator

will turn off, the red light under

 

the Input Selector will flash on and off once and the

 

Program/SPL Indicator

 

will flash green three times to

 

indicate that the codes have been erased.

To erase all codes that have been programmed to all devices in the remote, follow these steps:

1. Press any Input Selector 0 and also the Learn button

.

2.When the red LED under the Input Selector turns red and the

Program/SPL Indicator flashes amber, release the buttons.

3.Press and release the same Input Selector 0 again.

4.

Press the 9 button

three times.

5.

The Program/SPL Indicator

will turn off, the red light under

 

the Input Selector will flash on and off once and the

 

Program/SPL Indicator

 

will flash green three times after

 

some seconds to indicate that the codes have been erased.

Macro Programming

Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the CS’s remote control. Once programmed, a macro will send out up to 19 different remote codes in a predetermined sequential order, enabling you to automate the process of turning on your system, changing devices, or doing other common tasks. The CS remote can store up to four separate macro command sequences, that are accessed by pressing the Macro K buttons

1.To start programming a macro, press the Mute A button and the Macro K button to be programmed at the same time. Note that

the latest selected Input Selector 0 will light red, and the

Program Indicator

will flash amber.

2.Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program Indicator

will flash green twice to confirm each button press as you enter commands.

NOTE: While entering commands for Power On of any device during a macro sequence, press the Mute A button. DO NOT press the Power ON 0 button.

English

29

Image 29
Contents OWNER’S Guide Table of Contents Thank you for choosing JBL Description and FeaturesIntroduction Safety Information Terminology Features Power On/Off Standby Press the button once to turn Power On/Off Standby Headphone Jack Open/CloseFRONT-PANEL Controls  Main Information DisplayFRONT-PANEL Display Disc Type IndicatorsRepeat Indicators REAR-PANEL Connections REAR-PANEL Connections Remote Control Remote Control Basic Information Installation and Connections Optional Audio Connections Aux Input for External Source Speaker PlacementAux Output for Recording Digital In- and OutputsBasic Playback Preparation Connecting the AC PowerFirst Turn-On Fast-Motion Playback/Fast Search Disc Playback Features Skipping Tracks or Titles/ChaptersFreeze Frame and Frame Advance With DVD Only Slow-Motion Playback With DVD OnlySystem Defaults System SetupSetup Menu System SettingsAudio Settings Output Level Adjustment Audio AdjustmentDelay DivX Video On Demand Video AdjustmentTest Screen PLAYER/RADIO Menu Using the Status Bar MenuDisc Shows the type of the disc Information DisplaysRearranging the Station List Selecting PresetsRadio Menu Auto Preset Function Removing PresetsSurround Mode for Tuner RDS Station IDTV Menu TV MENU, AUX MENU, Digital in MenuAUX Menu Digital In MenuSurround Modes USB Menu Program Indicator Learning Codes from a Remote ControlErasing Learned Codes Macro ProgrammingWhen the Program Indicator Erasing Macro CommandsPress the TV Selector ErasedDVD Language Codes Troubleshooting Subtitles cannot be turned off when you play a DVD Audio language cannot be changed when you play a DVDAngles cannot be changed when you play a DVD Disc does not playGlossary Specifications PRO Sound Comes Home Declaration of Conformity