Lanzar Car Audio MAXP 2960, MAXP 2760, MAXP 4260 user manual ~COl~6fJLrr

MAXP4260 4 CHANNEL AMPLIFIER APPLICATIONS

4 CHANNEL FULL RANGE SYSTEM

Here we show how to use the 4 channel amplifiers as straightforward discrete 4 channel full range units.

Interconnect c.ble checldlst:

-Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables,

SWItch .enlng checklist:

-ljZCH X'()VER: FULL	-3/4CH X'()VER: FULL
Crossover frequency control checklist:
Channel. I/Z:	Channel. 3/4:
-HIGH PASS: NfA	-HIGH PASS: NfA
-LOW PASS: NfA	-LOW PASS: NfA

Level control checklist:

-Refer to the section "setting up systems after installation for best performance"

Minimum flnalloud.......ker Impedance.:

.. Z ohm per ch.nnel.

Z or 3 CHANNEL FULL RANGE SYSTEM

	~
			I"	"
FUIl..RANGE co			~'~.~"
STERfOUNE '"			~I~· .2
INPUTS			P i
~			~.
			~
			~IlooJ
			0
			~~I
			I~
			~"
		u

='-"~

~COl~6(fJLrr

=-r=

		..j	FUll RANGE
			SPEMERS
~	f!		JitO
~		D	to
	L
~			to
	[1
~	[:g		to
~	I		TOBATTERY+I2V
			VIII FUSE
~	:.	:Ii	REMOTE TURN-ON
			CHI\S5IS GROUND
~		or

l~

Here we show how to use the 4 channel amplifiers as full range

2or 3 channel units by taking advantage of the mono bridging capability of alllanzar MAX PRO series amplifiers.

The follwing example shows how to create a 3 channel system

by mono bridging channel pair 3/4. In order to create a 2 channel system. simply follow the example to also mono bridge channel pair 1f2,

TIP: If you are using the mono sub bass output of an active crossover, there is nothing wrong with switching in the low pass filter in these amplifiers for a steeper low pass rolloff.

Level control checkli.t:

- Refer to the section "Setting up systems after installation for best performance"

Minmum final loudspeaker impedances:

- 2 ohm per channel in stereo mode. - 4 ohm mono bridged.

Interconnect cable checklist:

-Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head unit with good quality RCA cables.

-A MONO signal source is required to bridge channel pair3/4, such as would be available from the mono sub bass output of an active crossover, whether standalone, or built into a head unit or equalizer. Important: Do not be tempted to connect the hot. or positive outputs, from any source together to obtain a mono signal, as this could very well damage the outout stage of that source,

-It is necessary to feed the SAME signal to both lett and right inputs via a Y-adapter RCA cable.

-Connect the mono speaker positive terminal to the RIGHT +, and its negative terminal to LEFT - as shown.

SWItch .enlng checklist:

-I/ZCH X'()VER: FULL -3/4CH X'()VER: FULL

1STEREO I MONO

FUll. RANGE

UNE INPI./n

STEREO

FULL AANGE

!tjOR HIGHS

• SPENCERS

STEREO ffiFUll. RANGE + ORHIGHS

SPEAKERS

TO Bll.TTERY+1ZV

VIA FUSE

REMOTE TURN-ON

CHASSIS GROUND

Cros.over frequency control checkli.t:

chennel. I/Z:	channel. 3/4:
- HIGH PASS: NfA	_HIGH PASS: NfA
- LOW PASS: NfA	_LOW PASS: NfA
-