Page 3
SECTION 3 - OPERATION
| Pool |
|
|
| ° | Desired Temp |
|
|
| |
| Spa |
|
|
| Water Temp |
|
|
| ||
| Cooling | 78 | Heating |
|
|
| ||||
| POOL | UP | DOWN | MODE |
|
|
| |||
| SPA |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Figure 4 |
|
|
| ||
INDICATOR LIGHTS |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |
| LIGHTS |
|
|
| EXPLANATION |
| SUPPLEMENTAL INFORMATION |
| ||
|
|
|
|
|
|
|
|
|
| |
| “Pool” |
|
|
| Pool Thermostat Selected |
|
|
| ||
| “Spa” |
|
|
| Spa Thermostat Selected |
|
|
| ||
| “Cooling” |
|
|
| Actively Cooling Water |
| Not applicable for Straight Heat models. |
| ||
| “Desired Temp” |
|
|
| Setting Desired Water Temperature |
|
|
| ||
| “Water Temp” |
|
|
| Actual Water Temperature |
|
|
| ||
| “Heating” |
|
|
| Actively Heating Water |
|
|
| ||
|
|
|
|
|
|
|
|
| Table 3 | |
BUTTONS |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
| BUTTONS |
|
|
| EXPLANATION |
|
| SUPPLEMENTAL INFORMATION |
| |
|
|
|
|
|
|
|
|
| ||
| “Pool / Spa” |
|
| Select between Pool and Spa |
|
| Please note – this does not turn off equipment. It only allows a user to |
| ||
|
|
|
|
|
|
|
|
| toggle between the Pool thermostat and the Spa thermostat. |
|
| “Up” |
|
| Select to raise temperature set |
|
|
|
| ||
|
|
|
| point or move up in a menu choice |
|
|
|
| ||
| “Down” |
|
| Select to lower temperature set |
|
|
|
| ||
|
|
|
| point or move down in a menu |
|
|
|
| ||
|
|
|
| choice |
|
|
|
|
| |
| “Mode” |
|
| Select a mode |
|
|
| Modes available are “ACH”, “COOL”, “HEAT”, and “OFF”. |
| |
|
|
|
|
|
|
|
|
| Please note – “ACH” and “COOL” only available on some models. |
|
|
|
|
|
|
|
|
|
| Table 4 | |
DISPLAY |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
| MESSAGE |
|
|
| EXPLANATION |
| SUPPLEMENTAL INFORMATION |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| A numeric code is required before any temperature adjustment can |
|
|
|
|
|
| A user lockout code has been |
| be entered. Use the “UP” or “DOWN” arrow to enter code, then select |
| ||
| “000” |
|
|
|
| “MODE” to temporarily unlock Heat Pump. If code is unknown, a re- |
| |||
|
|
|
| activated. |
|
|
|
| ||
|
|
|
|
|
|
|
| set option is available in product manual. Manuals can be |
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| downloaded from www.AquaCal.com. |
|
|
|
|
|
|
|
|
|
| When this mode is active, the heat pump will automatically switch |
|
| “ACH” |
|
|
|
| between heating and cooling modes to maintain a set temperature |
| |||
|
|
|
|
|
|
|
|
| point within ± 3 degrees. Feature available for Heat & Cool units. |
|
| “COOL” |
|
|
| Cooling Mode |
|
|
| Heat Pump is set to cool the water. Feature available for Heat & Cool |
|
|
|
|
|
|
|
| units. |
| ||
|
|
|
|
|
|
|
|
|
| |
| “HEAT” |
|
|
| Heating Mode |
|
|
| Heat Pump is set to heat water. |
|
|
|
|
|
|
|
|
|
| Heat Pump can be turned off by using “MODE” button or setting |
|
| “OFF” |
|
|
| Unit off |
|
|
| temperature below 45 degrees. Heat Pump will not allow a set |
|
|
|
|
|
|
|
|
|
| temperature to be programmed until turned on again. |
|
| “xx°” |
|
|
| Current Water Temperature |
| Temperature can be set from 45° F to 104° F. This can be displayed |
| ||
|
|
|
| (Example 78°) |
|
|
| in Fahrenheit or Celsius depending on programming. |
| |
|
|
|
|
|
|
|
|
| ||
| FLO |
|
|
| No water flow through Heat Pump |
| This can be a normal display depending on system settings. See |
| ||
|
|
|
|
| “Troubleshooting” if needed. |
| ||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Table 5 |