English-29, Connect a PC and MultiSync LCD5710

3.Reducing the environmental temperature is effective for long life use.

When Protection board (glass, acryl) is installed over the LCD surface, enclosed into the box / wall, or stack the monitor, please utilize the temperature sensors inside monitor.

To reduce the environmental temperature, the monitor should be set Low Brightness or Cooling Fan "ON" by using Screen sever Function.

4.Please use "Screen Saver Mode" of monitor.

NOTE 2: MONITOR ID and IR CONTROL

Using the one PC or one infra-red wireless controller, you can control up to 26 MultiSync LCD5710 that are connected by daisy chained RS-232C.

1.Connect a PC and MultiSync LCD5710.

Connect a PCÕs RS-232C control output to the MultiSync LCD5710Õs RS-232C input.

You can connect other MultiSync LCD5710; Connect MultiSync LCD5710Õs RS-232C output to other MultiSync LCD5710Õs RS-232C input. (Refer to page 30).

2.Set Monitor ID.

Set ÒMONITOR IDÓ in the ÒADVANCED OPTIONÓ menu.

ÒMONITOR IDÓ should be set to a unique number on all daisy chained MultiSync LCD5710 from 1 to 26. We recommend numbering continuously from 1 in a sequential number.

Set ÒPRIMARYÓ to ÒIR CONTROLÓ in the ÒADVANCED OPTIONÓ menu on the first of the daisy chained monitors. Set ÒSECONDERYÓ to ÒIR CONTROLÓ on other monitors.

3.Press “DISPLAY” button aiming at the “PRIMARY” monitor then ID select OSM will be shown at top left side of the screen.

English

	ID: 1 <- ID number itself.	ID: 1
	ID No.: 1 <- ID number of the controllable monitor.	ID: 1
	ID No.: 1 <- ID number of the controllable monitor.	ID No: 2
	Press Ò+Ó button to increase this ÒID No.Ó.
	Press Ò-Ó button to decrease it.
	If you control all the daisy-chained monitors at the same time,
	please select ÒID No.Ó ÒALLÓ.
	please select ÒID No.Ó ÒALLÓ.

4.Operate wireless remote controller with aiming at the “PRIMARY” monitor. The ÒMENU OSMÓ will appear on the selected ID No.Õs monitor.

Monitor ID

"Monitor ID" which you want to control

NOTE: If ÒID No.Ó select OSM is showing at the ÒPRIMARYÓ monitor, press ÒDISPLAYÓ button to clear this OSM.

HINT: If you lost control by a reason of wrong setting ÒIR CONTROLÓ, keep pressing during 5 sec or more the ÒDISPLAYÓ button. The monitor will reset ÒIR CONTROLÓ to ÒNORMALÓ.

NOTE 3: HOW TO SETUP SCHEDULE

Using the ÒSCHEDULEÓ function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated. You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will use for each scheduled activation period. A check mark in the box next to the number of the schedule indicates that the selected schedule is in effect.

To select which schedule to set, use the up/down arrows to move the red bar vertically under the number (1 to 7) of the schedule.

Use the (+) and (-) buttons to move the red bar horizontally within the particular schedule. The ÒSETÓ button is used to make a selection. If you create a schedule but do not want to use a power on time, select Ò--Ó in the ÒONÓ time slot.

If you do not want to use a power off time select Ò--Ó in the OFF time slot.

If there is no input selected (Ò--Ó showing in the input spot) the input from the previous schedule will be used.

The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly. When schedules are overlapping, scheduled Power ON time has priority over scheduled Power OFF time.

If there are two schedules programmed for the same time, then the highest numbered schedule has priority. When the ÒOFF TIMERÓ (see page 25) is set, the ÒSCHEDULEÓ function is disabled.

English-29

Downloaded From TV-Manual.com Manuals