Panasonic CQ-VA707N operating instructions ID Code Input, Loud beep sounds for 10 seconds

Page 20

ID Code Input

¡When removing the unit from the car and mounting it on another car,

¡When replacing a car battery with a new one, or other cases

When the unit is disconnected from the main power supply such as the above cases, follow the proce- dure below.

Note: All settings return to the default setting except ID code.

E

N

G

L

I

S

H

18

[MODE]

MUTE

[PWR](Power)

PWR

TRACK

qPress [PWR] or [MODE] to switch on the power.

*When using the display unit, press [MODE](PWR) to switch on the power.

The loud beep sounds for 10 seconds.

w Press [ ](OPEN/CLOSE) to raise the display unit during the loud

beep is sounding.

DISC/BAND

ENTER

NAVIGATION

MODE NAVI MENU

CHz CHx TITLE

1 2 3

RANDOM SCAN REPEAT

4 5 6

TA AF PTY

ASPECTOPEN/CLOSE

A LOC

Car AV

[

](OPEN/CLOSE) Numeric button

 

CH·C

TV

EON*PTY*CT

 

 

 

MODEMODE

TILT

OPEN/CLOSE

 

PWR 7.0'' WIDE COLOR LCD MONITOR WITH RECEIVER

[MODE]

[

](OPEN/CLOSE)

* The display unit is not raised even if you press [ ] after the loud

beep stops. In such a situation, switch off the power and try the

procedure again.

eID code input screen is displayed. Enter the ID code using the remote control.

success

Note: When failing in entering ID code, a screen on the right is dis- played, and the unit beeps three times. Enter a correct ID code.

In case of failing in entering ID code three times consecutively, the power is turned off. Turn on the power again and enter a correct ID code in this case.

Notes:

¡Press [MODE] to close the main menu and the setting/adjusting menu.

¡Press [MENU] in the setting/adjusting menu to return to the main menu mode.

¡The setting/adjusting menu is automatically closed if no operation is performed for about 10 seconds.

21

CQ-VA707N

Image 20
Contents Panasonic Contents ¡7-inch wide LCD color display Features¡ID code setup ID Code PrecautionsWhen Driving Remote Control Preparation Battery InsertionBattery Notes Insert the batteryRemote Control Unit Names of ControlsRemote Remote Control Sensor Display UnitFront Control Unit Front See pages 55 to 61 about electrical connectionsPower on Power offHow to Open and Raise the Display Before UseDisplay Unit Lateral Angle Adjustment Slip part in the upper half of it, Adjust its lateral angleTilt SlideFolding Down the Display Temporarily Retracting the DisplayUsing the Menu/Menu Control Menu TreeSetting/Adjusting Menu Main MenuUser Settings Monitor Position TILT/SLIDESlide Tilt Press or toClock Setting Clock Clock ModeClock Display Select Display On Clock display is on OFF Clock display is offNavigation Set Up Navi SET UP ID Code ID-CODE Setting How to enter your ID code For the first timeHow to change your ID code ID Code Input Loud beep sounds for 10 secondsInput Selection Input Select NaviCamera OFFConnection example Panasonic Car Navigation System CN-DV2000ENOther corporations’ car navigation sys- tem RGB connectionRear View Camera TV Tuner CY-TN1500PENOthers equipment such as video camera Connect to a video input of VTR1 or VTR2VTR2 Example of connecting to two or more productsRGB Car Navigation TV Tuner CY-TN1500PEN and RearView Camera a car navigation system is ACC Selection ACC If your car has no ACC, be sure to use a default, ACC OFFMerits when ACC is activated Balance/Fader Sound SettingsTone Bass/Treble Loudness BeepMenu Press or to selectContrast Screen AdjustmentDimmer Brightness ColorTint TintVolume Changing the Operation ModeOperation General MuteDisplaying the Car Navigation Screen Radio Basics Station Preset Tuning in to a Preset StationManual Station Preset Auto Station PresetRadio Data System RDS Traffic AnnouncementsProgram Type Display Emergency Announcement ReceptionAlternative Frequency AF AF1Region Setting Region on Region OFFSeek tuning and auto preset memory TA VolumeMuting in TA Mode Traffic Announcement TATA Volume TA Volume UMEProgram Type PTY Display PTY LanguagePTY Selection Speech → MusicPTY Search PTY PresetPTY Preset Change PTY Language Press Enter to set the PTY languageCD Changer Basics Starting the CD ChangerTitle Display Changer ControlTrack Random Only for remote control Disc Random Only for remote controlTrack Selection Track SearchTrack Scan Only for remote control Disc Scan Only for remote controlTrack Repeat Only for remote control Disc Repeat Only for remote controlDual CD Changer Only for remote control VTR Mode Press Mode to change to VTR1 mode or VTR2 mode as followsExample of VTR1 mode Alarm indicator AuxiliaryAspect Ratio for VTR Mode NormalFull ZoomInstallation Installation OpeningTransportation bracket removal But not more thanInstallation Precautions Installation Procedures Secure the rear of the unitUsing the Rear Support Strap u Diagram QtyMounting the Control Unit Mounting ExampleConnecting the Power Source Basic SystemElectrical Connections Rear Amplifiers CY-M9054EN and CY-M7052EN Electrical ConnectionsExample 2 Advanced System CQ-VA707N Example 3 Connection with two CD Changers CX-DP9061EN You need the optional dual changer control unit CA-CD55ENConnecting the Parking Brake Connection Lead Connecting the Reverse CordParking brake switch position Varies with the vehicle modelTroubleshooting MaintenanceTroubleshooting Tips Error Display Message CD ChangerPower Display Possible Cause Problem Probable SolutionGeneral DisplayRadio Remote ControlVTR, AV, Camera Video, Video Camera, Rear View Camera Clean dirt by wiping lightly with a soft cloth Kitchen cleanser diluted with waterWill result in discoloration or removal of the paint Damage the surface of the unitSpecifications Central P.O. Box 288, Osaka 530-91, Japan