Panasonic CQ-VA707N operating instructions Precautions, ID Code, When Driving

Page 4

WARNING:

TO AVOID THE RISK OF SERIOUS INJURY OR POSSIBLE VIOLATION OF LAWS, DO NOT USE WHERE VISIBLE TO DRIVER FOR ANY PURPOSE OTHER THAN NAVIGATION OR USE WITH REAR VIEW CAMERA.

When Driving

¡The driver must not operate the color LCD monitor. Operating the color LCD monitor may lead to dis- traction and cause an accident. Stop your vehicle in a safe location when operating the unit.

¡The driver must not watch videos while driving. It may lead to distraction and cause an accident.

¡Keep the unit at an appropriate sound level. Driving with the sound at a level that prevents you from hearing sounds outside and around the vehicle may cause an accident.

E N G L I S H

2

Precautions

Car Washing

To avoid electrical shorts which may cause a fire or other damage, do not expose this product to water or excessive moisture.

Car Ventilation

If your car is parked for several hours in direct sunlight, the temperature inside the car may become very high. It is advisable to drive the car and give the interior a chance to cool down before switching the unit on.

Power Supply

This product is designed to be used in a car hav- ing a 12-volt negative ground battery system.

Service

This product is made of precision parts. Do not attempt to disassemble or adjust any parts. For repair, please consult your nearest authorized Panasonic Service Center.

About Preset Memory

The preset memory is cleared to return to the orig- inal factory setting when the power connector or battery is disconnected.

For Installation

¡Install the monitor in a position that does not obstruct the driver’s vision.

¡Do not install the control unit in the following types of location:

A location which is exposed to water, a location where it could be stepped on, or a location which is exposed to hot air such as near a heater duct.

¡Do not install the unit in an area where it would obstruct the operation of an air bag.

¡Ask a trained technician to install the unit. Installation and wiring require training and expe- rience.

To be safe, ask the sales outlet where you pur- chased the unit to perform the installation.

When Operating

¡Do not let the unit fall or be strongly impacted since this may cause a malfunction or fire.

When Parked

¡Do not watch the monitor with the engine off. It will consume battery power and may prevent the engine from starting.

ID Code

Prior to operating this unit, it is a advisable to assign your 4-digit ID code for security. (The figures 1 to 6 can be used. The figures 7 to 9 and 0 are not available. Make sure to use four digits for ID code. ID code can not be set with two or three digits.)

Once the ID code has been set, the unit cannot be operated if the main power supply is disconnected then re-connected. It is electronically locked up so that the thief could not use the stolen unit unless that person knows the code you have set.

The ID code operation must be performed only by the person whom the unit belongs to.

Generally, it is not necessary to enter the ID code each time when using the unit if it has never been dis- connected from the main power supply (car battery). For the ID code setting procedures, see pages 19 to 21.

Caution:

Record your registered ID code and keep it in a secure location.

If you forget it, you will be unable to use the unit.

5

CQ-VA707N

Image 4
Contents Panasonic Contents ¡ID code setup Features¡7-inch wide LCD color display When Driving PrecautionsID Code Remote Control Preparation Battery InsertionBattery Notes Insert the batteryRemote Control Unit Names of ControlsRemote Remote Control Sensor Display UnitFront Control Unit Front See pages 55 to 61 about electrical connectionsPower on Power offHow to Open and Raise the Display Before UseDisplay Unit Lateral Angle Adjustment Slip part in the upper half of it, Adjust its lateral angleTilt SlideFolding Down the Display Temporarily Retracting the DisplayUsing the Menu/Menu Control Menu TreeSetting/Adjusting Menu Main MenuUser Settings Monitor Position TILT/SLIDESlide Tilt Press or toClock Setting Clock Clock ModeClock Display Select Display On Clock display is on OFF Clock display is offNavigation Set Up Navi SET UP ID Code ID-CODE Setting How to enter your ID code For the first timeHow to change your ID code ID Code Input Loud beep sounds for 10 secondsInput Selection Input Select NaviCamera OFFConnection example Panasonic Car Navigation System CN-DV2000ENOther corporations’ car navigation sys- tem RGB connectionRear View Camera TV Tuner CY-TN1500PENOthers equipment such as video camera Connect to a video input of VTR1 or VTR2RGB Example of connecting to two or more productsVTR2 View Camera a car navigation system is TV Tuner CY-TN1500PEN and RearCar Navigation Merits when ACC is activated If your car has no ACC, be sure to use a default, ACC OFFACC Selection ACC Tone Bass/Treble Sound SettingsBalance/Fader Loudness BeepMenu Press or to selectDimmer Screen AdjustmentContrast Brightness ColorTint TintVolume Changing the Operation ModeOperation General MuteDisplaying the Car Navigation Screen Radio Basics Station Preset Tuning in to a Preset StationManual Station Preset Auto Station PresetRadio Data System RDS Traffic AnnouncementsProgram Type Display Emergency Announcement ReceptionAlternative Frequency AF AF1Region Setting Region on Region OFFSeek tuning and auto preset memory TA VolumeMuting in TA Mode Traffic Announcement TATA Volume TA Volume UMEProgram Type PTY Display PTY LanguagePTY Selection Speech → MusicPTY Preset Change PTY PresetPTY Search PTY Language Press Enter to set the PTY languageCD Changer Basics Starting the CD ChangerTitle Display Changer ControlTrack Random Only for remote control Disc Random Only for remote controlTrack Selection Track SearchTrack Scan Only for remote control Disc Scan Only for remote controlTrack Repeat Only for remote control Disc Repeat Only for remote controlDual CD Changer Only for remote control VTR Mode Press Mode to change to VTR1 mode or VTR2 mode as followsExample of VTR1 mode Alarm indicator AuxiliaryAspect Ratio for VTR Mode NormalFull ZoomInstallation Installation OpeningTransportation bracket removal But not more thanInstallation Precautions Installation Procedures Secure the rear of the unitUsing the Rear Support Strap u Diagram QtyMounting the Control Unit Mounting ExampleConnecting the Power Source Basic SystemElectrical Connections Rear Example 2 Advanced System Electrical ConnectionsAmplifiers CY-M9054EN and CY-M7052EN CQ-VA707N Example 3 Connection with two CD Changers CX-DP9061EN You need the optional dual changer control unit CA-CD55ENConnecting the Parking Brake Connection Lead Connecting the Reverse CordParking brake switch position Varies with the vehicle modelTroubleshooting MaintenanceTroubleshooting Tips Error Display Message CD ChangerPower Display Possible Cause Problem Probable SolutionGeneral DisplayVTR, AV, Camera Video, Video Camera, Rear View Camera Remote ControlRadio Clean dirt by wiping lightly with a soft cloth Kitchen cleanser diluted with waterWill result in discoloration or removal of the paint Damage the surface of the unitSpecifications Central P.O. Box 288, Osaka 530-91, Japan