Pioneer VSX-01THX Minute guide, Playing a source, Problems when using the Auto Mcacc Setup

5 minute guide 02

•With error messages (such as Too much ambient noise! or Check Microphone.) select RETRY after checking for ambient noise (see Problems when using the Auto MCACC Setup on page 11) and verifying the mic connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

1.Auto	MCACC			1.Auto	MCACC
Now	Analyzing…		(2/9)			CHECK
				Front	[ YES ]
				Center	[ YES ]
Environment Check				Surr	[ YES ]
Ambient Noise		[	OK ]	SB	[ YES x 2 ]
Microphone		[	]	SW	[ YES		]
Speaker YES/NO		[	]
						OK
		:Cancel		ENTER:Next			:Cancel

The configuration shown on-screen should reflect the actual speakers you have.1

If you see an error message (ERR) in the right side column (or the speaker configuration displayed isn’t correct), there may be a problem with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use / to select the speaker and / to change the setting (and number for surround back) and continue.

6Make sure ‘OK’ is selected, then press ENTER. A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for Channel Level, Speaker Distance, Standing Wave and Acoustic Cal EQ.

Again, try to be as quiet as possible while this is happening. It may take 3 to 7 minutes.

7 The Auto MCACC Setup has finished! Press RETURN to go back to the System Setup menu.2

Be sure to disconnect the microphone from this receiver upon completion of the Auto MCACC setup.

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the

System Setup menu (starting on page 38).3

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary. If there are any instructions showing in the front panel display, please follow them.

•Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV when doing the Auto MCACC Setup.

Playing a source

Here are the basic instructions for playing a source (such as a DVD disc) with your home theater system.

				4	5	6
RECEIVER			SOURCE	SR+	SBch	A.ATT	CATEGORY			RETURN
				7	8	9
				D.ACCESS	CH LEVEL	CLASS		SETUP	TUNE
DVD	BD	TV	HDMI		0	ENTER	iPod CTRL
					INPUT	MASTER
						VOLUME	AUTO/	STEREO/		BD MENU
DVR 1	DVR 2	CD	CD-R				DIRECT	A.L.C.	STANDARD ADV SURR
				TV CONTROL			HDD	DVD
FM/AM	XM	SIRIUS	iPod USB				THX	STATUS		PHASE
				CH	VOL	MUTE
INPUT
			DIMMER				ANT		MPX	SIGNAL SEL
SELECT
1		2	3	AUDIO		VIDEO				MEM
				PARAMETER		PARAMETER	AUDIO	DISPLAY		CH
GENRE	MCACC		SLEEP	EXIT	TUNE	TOOLS

4 5 6

1Switch on your system components and receiver. Start by switching on the playback component (for

example a DVD player), your TV4 and subwoofer (if you have one), then the receiver (press  RECEIVER).

• Make sure the setup mic is disconnected.

2 Select the input source you want to play.

You can use the input source buttons on the remote control, INPUT SELECT, or the front panel controls.5

3Press AUTO/DIRECT (AUTO SURR/STREAM DIRECT) to select ‘AUTO SURROUND’ and start

playback of the source.6

If you’re playing a Dolby Digital or DTS surround sound DVD disc, you should hear surround sound. If you are playing a stereo source, you will only hear sound from the front left/right speakers in the default listening mode.

•See also Listening to your system on page 30 for information on different ways of listening to sources.

Note

1If you’re using the front panel display, the diagram in Listening to Surround Sound on page 9 indicates (in bold) how each speaker is displayed.

2You can also choose to view the settings from the MCACC Data Check screen. See Automatic MCACC (Expert) on page 38 for more on this.

3• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual speaker setup on page 48.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

4Make sure that the TV’s video input is set to this receiver (for example, if you connected this receiver to the VIDEO 1 jacks on your TV, make sure that the VIDEO 1 input is now selected).

5If you need to manually switch the input signal type press SIGNAL SEL (page 33).

6• You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS and 88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.

•Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a multichannel listening mode (see Listening in surround sound on page 30 if you need to do this) if you want multichannel surround sound.

11

En