Pioneer VSX-01THX operating instructions Video, Settings

Page 85

Additional information

13

Video

Symptom

Remedy

No image is output when an

• Check the video connections of the source component (see page 18).

input is selected.

• For high-definition video (using component video connections), or when digital video conversion

 

is switched off (in Setting the Video options on page 74), you must connect your TV to this receiver

 

using the same type of video cable as you used to connect your video component.

 

• Make sure the input assignment is correct for components connected using component or HDMI

 

cables (see The Input Setup menu on page 69).

 

• Check the video output settings of the source component.

 

• Check that the video input you selected on your TV is correct.

 

• Some components (such as video game units) have resolutions that may not be converted. If

 

adjusting this receiver’s Resolution setting (in Setting the Video options on page 74) and/or the

 

resolution settings on your component or display doesn’t work, try switching Digital Video

 

Conversion (in Setting the Video options on page 74) OFF.

 

 

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video

 

cable is used for connecting both the recorder and the video source (the one you want to record) to

 

this receiver.

 

 

Noisy, intermittent, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the

picture.

video quality may just be poor (with some video game units, for example). The picture quality may

 

also depend on the settings, etc. of your display device. Switch off the video converter and reconnect

 

the source and display device using the same type of connection (component, S-Video or

 

composite), then start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see

continually shows an error.

also Problems when using the Auto MCACC Setup on page 11). If the noise level cannot be kept low

 

enough, you will have to set up the surround sound manually (page 41).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.

Setup, the speaker size setting

Switch off all other appliances in the room and use Auto MCACC Setup again.

is incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some

 

cases. Change the speaker setting manually in Speaker Setting on page 48, and use the ALL (Keep

 

SP System) option for the Custom Menu in Automatic MCACC (Expert) on page 38 if this is a

 

recurring problem.

 

 

Can’t adjust the Fine Speaker

• Check that the speakers are all in phase (make sure the positive (+) and negative () terminals are

Distance setting (page 42)

matched up properly).

properly.

 

The display shows KEY LOCK ON when you try to make settings.

With the receiver in standby, press  STANDBY/ON while holding down the SPEAKERS button to disable the key lock.

Most recent settings have been • The power cord was disconnected from the wall while adjusting this setting. erased.

85

En

Image 85
Contents Operating Instructions Federal Communications Commission Declaration of Conformity Operating EnvironmentKeep in a Secure AREA. this is for Your Security Information to UserRisk of Electric Shock Do not Open Wash hands after handling Contents Using other functions Other SettingsOther connections Hdmi ControlBefore you start FeaturesBefore you start Chapter Before you start Installing the receiverChecking what’s in the box Loading the batteriesMinute guide Chapter Minute guideIntroduction to home theater Listening to Surround SoundStart Minute guide Problems when using the Auto Mcacc SetupPlaying a source Select the input source you want to playPhase Control on Better sound using Phase ControlPhase Control OFF Phase Control indicator on the front panel lightsConnecting your equipment Chapter Connecting your equipmentRear panel Connecting your equipment About the video converter Connecting your equipmentAbout Hdmi Connecting your equipment Connecting using HdmiConnecting your Blu-ray disc player Connecting your equipment Connecting your TV and DVD playerConnect using an Hdmi cable For a second recorder, use the DVR2 in inputs Connecting digital audio sources Using the component video jacksUse an optical cable for the connection.2 Use a three-way component video cableConnecting a component to the front panel inputs Connecting analog audio sourcesAbout the WMA9 Pro decoder Use a coaxial cable for the connectionConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsBanana plug connections THX speaker system setup Connecting antennasPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Chapter Controls and displaysFront panel 12 13Controls and displays Operating range of remote control unitSpeakers Controls and displays Display RECEIVER Controls and displays Remote controlSOURCE TV CtrlMute ReceiverListening to your system Chapter Listening to your systemListening in surround sound Auto playbackUsing the Advanced surround effects Using the Home THX modesListening to your system THX SELECT2 GamesListening in stereo Using Front Stage Surround AdvanceTip Selecting Mcacc presets Listening to your system Using Stream DirectChoosing the input signal Hdmi Digital AnalogUsing the Virtual Surround Back mode Using surround back channel processingAuto Analog 2-channel stereo sources Pro and DVD-Audio stereo sourcesDTS-HD Master Audio/DTS-HD DTS-EXPRESS encoded stereo SourcesUsing the tuner Chapter Using the tunerSaving station presets Listening to the radioNaming station presets Using the tunerListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu Chapter System Setup menuMaking receiver settings from the System Setup menu Select the setting you want to adjustOptions are ALL , Keep SP System , 6 Speaker System Setup menuPro. & S-Wave If necessary, confirm the speaker configuration in the OSD.1 Manual Mcacc setup Surround back speaker settingSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Adjust the level of the left channelFine Channel Level Fine Speaker DistanceStanding Wave Acoustic Calibration EQ AdjustHow to interpret the graphical output How to use Acoustic Calibration EQ ProfessionalAcoustic Calibration EQ Professional Select ‘EQ Professional’, then press Enter Using Acoustic Calibration EQ ProfessionalSelect an option and press Enter Data Management Select ‘Data Management’ from the System Setup menuCopying Mcacc preset data Checking Mcacc preset dataRenaming Mcacc presets Clearing Mcacc presetsSpeaker Setting System Setup menu Manual speaker setupSelect ‘Manual SP Setup’, then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menuConfirm your selected setup option Select a setup optionAdjust the level of each channel using / Channel LevelSpeaker Distance THX Audio SettingCurve 5e.THX Audio Setting Loudness Plus SB SP Position Finish Connecting your iPod to the receiver Connecting an iPodOther connections Other connections ChapterOther connections Switching the iPod controls2Basic playback controls ReturnConnecting your USB device to the receiver Other connections Connecting a USB deviceBasic playback controls No Device appears in the OSDConnecting your XM Radio receiver Using XM RadioCompressed audio compatibility Saving channel presets Using XM HD SurroundListening to channel presets Listening to XM RadioUsing the XM Menu Using Sirius RadioConnecting your SiriusConnect Tuner XM Menu provides additional XM Radio featuresPress / to select the channel preset you want Using the Sirius MenuSirius Menu provides additional Sirius Radio features.2 Listening to Sirius RadioSpeaker B setup Other connections Connecting the multichannel analog inputsSwitching the speaker system Selecting the multichannel analog inputsBi-amping your front speakers Bi-wiring your speakersConnect your speakers as shown below MULTI-ZONE listening Other connections Connecting additional amplifiersMaking MULTI-ZONE connections LargeBasic MULTI-ZONE setup Zone Using the MULTI-ZONE controlsSurround Back System MULTI-ZONE setup Zone MULTI-ZONE listening optionsMULTI-ZONE remote controls Connecting an IR receiverUse the Master Volume dial to adjust the volume Press ControlPioneer flat panel TV Using this receiver with a Pioneer flat panel TVUsing the SR+ mode with a Pioneer flat panel TV Advanced Mcacc output using your PC Other connections Connecting a PC for Advanced Mcacc outputSelect ‘Output PC’ and press Enter Setting the Hdmi Control mode Setting the Hdmi optionsHdmi Control Hdmi Control ChapterSynchronized amp mode Before using synchronizationHdmi Control About Hdmi ControlOther Settings Chapter Other SettingsInput Setup menu SetupOther Setup menu Other SettingsInput function default and possible settings Press Receiver on the remote control, then press SetupZone Audio Setup Multi Channel Input SetupOSD Adjustment SR+ Setup for Pioneer flat panel TVsSelect ‘SR+ Setup’ from the Other Setup menu Select the ‘PDP Volume Control’ setting you wantUsing other functions Chapter Using other functionsSetting the Audio options Press Return to confirm and exit the menuSetting the Video options Using other functionsDRC EffectSelect the source you want to record Making an audio or a video recordingPrepare the source you want to record Tune to the radio station, load the CD, video, DVD, etcSwitching the speaker impedance Using the sleep timerChecking your system settings Dimming the displayDefault system settings Using other functions Resetting the systemPress the front panel Auto SURR/STREAM Direct button Press Home THX to confirmSelecting preset codes directly Setting the remote to control other componentsPreset code list Controlling the rest of your systemControls for TVs Controlling the rest of your systemTV On or offControls for other components Menu Decide which component you want to use the remote sensor & Enter DisplayPower TroubleshootingAdditional information Additional information ChapterAdditional information Other audio problems Video SettingsProfessional Calibration EQ graphical output Signal SEL buttonDisplay USB interface Remote controlOther setting for your component Or other setting for your componentReceiver to a component or TV with the DeepColor feature Hdcp Error showsConfiguration B Configuration aImportant information regarding the Hdmi connection XM radio messagesSirius radio messages Dolby Additional information Surround sound formatsDTS Digital Surround Windows Media Audio 9 ProfessionalDTS Neo6 DTS 96/24Additional information About THX About Neural THX Surround About Sirius Additional information About XMAbout XM Radio XM Ready Legal XM Ready SubscriptionON/AUTO Stereo 2 channel signal formatsPRO Logic PRO Logic +THXPro Logic IIx Movie +THX a Pro Logic llx Multichannel signal formatsPro Logic llx Music +THX EX +THX Games b Pro Logic IIx Movie +THX aDTS +2 Pro Logic DTS +2 Pro Logic llxDTS +2 Pro Logic llx Movie +THX a DTS +Neo6 DTS +Neo6 +THX Cinema100 Not connected ConnectedCleaning the unit Additional information SpecificationsOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation