Pioneer P6800MP installation manual Connecting the Units

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

• When an external power amp is being used with

this system, be sure not to connect the blue/white

7When not connecting a rear speaker lead to a Subwoofer

<ENGLISH>

Power amp (sold separately)

MANUAL

DEH-P6800MP

MANUEL

ational vehicle, truck, or bus, check the battery

voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning

installation.

• Refer to the owner’s manual for details on

connecting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

lead to the amp’s power terminal. Likewise, do not

connect the blue/white lead to the power terminal

of the auto-antenna. Such connection could cause

excessive current drain and malfunction.

• To avoid a short-circuit, cover the disconnected

lead with insulating tape. Insulate the unused

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same

colors correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be connected

to a terminal coupled with ignition switch ON/OFF

operations. If this is not done, the vehicle battery

may be drained when you are away from the vehi-

cle for several hours. (Fig.1)

		CC
	F	A	O				F	O
			N					N
O	F					O	F
					S					S
					T					T
				R	A				R	A
			T					T
ACC position						No ACC position

Fig. 1

Antenna jack	Rear output
15 cm (5-7/8 in.)
	16 cm (6-1/4 in.)
	Front output

This product
Subwoofer output	IP-BUS input (Blue)

Fuse
(10 A)
Jack for the Wired Remote Control
Please see the Instruction Manual for the
Wired Remote Control (sold separately).		Multi-CD player
	IP-BUS cable	(sold separately)
	Blue/white
	To system control terminal of the power amp or
	Auto-antenna relay control terminal (max. 300
	mA 12 V DC).
Yellow/black
If you use an equipment with Mute function, wire this
lead to the Audio Mute lead on that equipment. If not,		+
keep the Audio Mute lead free of any connections.
		Front speaker
Yellow			≠
To terminal always supplied with power regardless of
ignition switch position.

Connecting cords with RCA pin plugs (sold separately)

System remote control

+

≠

Power amp (sold separately)

Power amp (sold separately)

Front speaker

INSTALLATION

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<XRD7112-A/N> UC <KMMZX> <05H00000>

D’INSTALLATION

the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

ance of 4 to 8 ohms. Connecting speakers with out-

put and/or impedance values other than those

noted here may result in the speakers catching fire,

emitting smoke or becoming damaged.

• When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.

Connect to an external power amp’s system remote

control or the car’s Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

•The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same

function.

Red

To electric terminal controlled by ignition switch (12

V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

Perform these connections when using the optional amplifier.

+	White	Gray	+
Front speaker
≠	White/black	Gray/black	≠
Left
+	Green	Violet	+
Rear speaker
≠	Green/black	Violet/black	≠
+			+
Rear speaker
≠			≠
+			+
Subwoofer
≠			≠

Front speaker

Right

Rear speaker

Rear speaker

Subwoofer

Fig. 2