Planar EP6504K/EP6504K-T LED Indicators, Using the Display in Portrait Mode, LED On, Condition

Page 28

LED Indicators

LED Indicators

The LED indicator light is located on the rear of the display near the keypad. The following table explains what the different colors and blink patterns mean.

 

LED On

 

 

Power Status

Condition

 

 

Green

Power on

 

 

Blinking Orange

No signal

 

 

Orange

Power saving mode

 

 

Off

AC off

 

 

Off

Power off

 

 

Using the Display in Portrait Mode

When using the display in the portrait position and looking at the rear of the display, it should be rotated according to the arrow stickers on the back of the display. This will allow for proper ventilation. Then select the OSD rotation of landscape or portrait

on the OSD menu (MAIN MENU > BASIC > OSD ROTATION).

Caution: Improper ventilation may shorten the life of the display.

22

EP5804K, EP5804K-T, EP6504K and EP6504K-T User Manual

Image 28
Contents EP5804K/EP5804K-T, EP6504K/EP6504K-T User Guide Trademark Credits Warranty and Service Plans RoHS Compliance StatementDisclaimer Table of Contents TCP Mode, UDP Mode and Uart Accessing Planar’s Technical Support Website Table of Contents Introduction Safety Information Safety PrecautionsImportant Safety Instructions Recommended Usage What is Temporary Image Retention?Burn-In Versus Temporary Image Retention European Union Disposal Information Normal Usage Guidelines Vesa Mounts, General DescriptionCooling Requirements Cleaning the Display Package Contents Description Quantity Contents of the Accessory Kit Part Installing the Cable Clips Dimensions EP5804KEP5804K T EP6504K EP6504K T Planar EP Series Standard Inputs DVI VGAInstalling the Display Before You Begin Installing OPS Expansion Optional Operating the Display OSD KeypadOSD Keypad Buttons Key DescriptionsRemote Control Receiver LED Indicators Using the Display in Portrait ModeLED On ConditionUsing the Remote Control Num Function Customer Hex Code Description SourceLocking/Unlocking the OSD Menus Function Customer Hex Code DescriptionChanging the Remote Control Battery Turning the Display OnAdjusting the Volume Turning the Display OffSelecting the Input Source OSD Menu Functions Mode3840x VideoMenu Video Description Setting Mode Menu, Adjust the image Position for VGA input 3840x Menu VideoDNS DVI Main Menu Submenu Description Setting Image Settings Display Settings OSD MenusAudio Settings Basic Settings RTC Submenus Advanced Settings Network Settings Navigating Through the Menus Multi-Display Control System StatusImage Settings Menu Scheme Brightness Contrast Sharpness Saturation HueRange 128~383 Range -50~50 Display Settings Menu Local DimmingAspect Ratio Zoom Auto Scan Select Source Range 0~10 Range On, OffAudio Settings Menu Range -6~6Basic Settings Menu Range 0~15Options On, Off Options 5~120Power LED Real Time Clock Splash Screen Real Time Timer Mode Basic Menu/RTC Real Time Clock MenuRTC Timer Mode User Timer Mode User modeRTC Timer Mode Work Days Timer Mode Work Days modeRTC Timer Mode All Days Timer Mode All Days modeAdvanced Settings Menu Auto Adjustment Image Position Phase Clocks VGA ADC SettingsIrfm OptionsDisplayPort Mode Factory Reset Enable Network Dynamic IP Static IP Address Subnet Mask Advanced Settings Ethernet Setup SubmenuOptions No, Yes Shows the unique address assigned to network interfaces Advanced Settings User ADC Calibration Advanced Settings Menu Monitor ID Video Wall Power On Delay Advanced Settings Multi-Display Control SubmenuOptions Yes, No Frame Matrix Matrix Y Division Division Y Advanced Settings Edid Setup DisplayPortSystem Status Menu Performing basic functions Using the Touch ScreenFunction Action Quickly drag your finger flick in a desired direction Touchscreen MultiTouch Driver Installation Touchscreen PQLabs MultiTouch Platform ContentUninstalling the MultiTouch Driver Multi-Touch FunctionsLAN Control Supported Operating SystemsInstallation Installation Installation Configuring Vcom Create a Remove an Virtual Search Function DescriptionsSearch By IP Configure IP Address WebAdding a Virtual COM Port Removing a COM Port Setting Up Email Alerts LoginLogin Authentication Configuration AdministratorSystem IP Configuration Load Default Setting Firmware Update and Boot Loader Upgrade TCP Mode, UDP Mode and Uart SmtpReset Device Timing Signal CompatibilityFH KHz FV Hz Timing KHzfH HzfV VesaSpecifications Model SpecificationAudio Input Humidity Troubleshooting Issue Check for the followingAccessing Planar’s Technical Support Website Index OPS expansion slot installation Iii