Planar EP6504K/EP6504K-T manual Shows the unique address assigned to network interfaces

Page 62

Advanced Settings Menu

Gateway

DNS Address

Save Network Settings

Email Alert

Load Default Settings

Device MAC

Set the gateway address when the DYNAMIC IP line is disabled or view it when the DYNAMIC IP line is enabled.

Range: 255.255.255.255 (0.0.0.0)

Set the DNS address when the DYNAMIC IP line is disabled or view it when the DYNAMIC IP line is enabled.

Range: 255.255.255.255 (0.0.0.0)

Save the network configuration when the DYNAMIC IP line is disabled. Options: No, Yes

Enable/disable the following email alerts:

POWER STATUS ALERT - Sent when the unit is turned on or off. SOURCE STATUS ALERT - Sent when a different source is selected. SIGNAL LOST ALERT - Sent when the input sync is lost.

Load default network settings

Options: No, Yes

Shows the unique address assigned to network interfaces.

56	EP5804K, EP5804K-T, EP6504K and EP6504K-T User Manual

Image 62

Contents EP5804K/EP5804K-T, EP6504K/EP6504K-T User Guide Disclaimer Warranty and Service Plans RoHS Compliance StatementTrademark Credits Table of Contents TCP Mode, UDP Mode and Uart Accessing Planar’s Technical Support Website Table of Contents Introduction Safety Information Safety PrecautionsImportant Safety Instructions Burn-In Versus Temporary Image Retention What is Temporary Image Retention?Recommended Usage European Union Disposal Information Cooling Requirements Vesa Mounts, General DescriptionNormal Usage Guidelines Cleaning the Display Package Contents Description Quantity Contents of the Accessory Kit Part Installing the Cable Clips Dimensions EP5804KEP5804K T EP6504K EP6504K T Planar EP Series Standard Inputs DVI VGAInstalling the Display Before You BeginInstalling OPS Expansion Optional OSD Keypad Buttons Operating the DisplayOSD Keypad Key DescriptionsRemote Control Receiver LED On LED IndicatorsUsing the Display in Portrait Mode ConditionUsing the Remote Control Num Function Customer Hex Code Description SourceLocking/Unlocking the OSD Menus Function Customer Hex Code DescriptionChanging the Remote Control Battery Turning the Display OnAdjusting the Volume Turning the Display OffSelecting the Input Source 3840x OSD Menu FunctionsMode VideoMenu Video Description Setting Mode Menu, Adjust the image Position for VGA input 3840x Menu VideoDNS DVI Main Menu Submenu Description Setting Image Settings Display Settings OSD MenusAudio Settings Basic Settings RTC Submenus Advanced Settings Network Settings Navigating Through the Menus Multi-Display Control System StatusImage Settings Menu Scheme Brightness Contrast Sharpness Saturation HueRange 128~383 Range -50~50 Aspect Ratio Zoom Auto Scan Select Source Display Settings MenuLocal Dimming Range 0~10 Range On, OffAudio Settings Menu Range -6~6Options On, Off Basic Settings MenuRange 0~15 Options 5~120Power LED Real Time Clock Splash Screen Real Time Timer Mode Basic Menu/RTC Real Time Clock MenuRTC Timer Mode User Timer Mode User modeRTC Timer Mode Work Days Timer Mode Work Days modeRTC Timer Mode All Days Timer Mode All Days modeAdvanced Settings Menu Auto Adjustment Image Position Phase Clocks VGA ADC Settings Irfm OptionsDisplayPort Mode Factory Reset Options No, Yes Advanced Settings Ethernet Setup SubmenuEnable Network Dynamic IP Static IP Address Subnet Mask Shows the unique address assigned to network interfaces Advanced Settings User ADC Calibration Advanced Settings Menu Options Yes, No Advanced Settings Multi-Display Control SubmenuMonitor ID Video Wall Power On Delay Frame Matrix Matrix Y Division Division Y Advanced Settings Edid Setup DisplayPortSystem Status Menu Function Action Using the Touch ScreenPerforming basic functions Quickly drag your finger flick in a desired direction Touchscreen MultiTouch Driver Installation Touchscreen PQLabs MultiTouch Platform ContentUninstalling the MultiTouch Driver Multi-Touch FunctionsLAN Control Supported Operating SystemsInstallation Installation Installation Configuring Vcom Create a Remove an Virtual Search By IP Function DescriptionsSearch Configure IP Address WebAdding a Virtual COM Port Removing a COM Port Setting Up Email Alerts LoginLogin System IP Configuration AdministratorAuthentication Configuration Load Default Setting Firmware Update and Boot Loader Upgrade TCP Mode, UDP Mode and Uart SmtpReset Device FH KHz FV Hz Signal CompatibilityTiming Timing KHzfH HzfV VesaSpecifications Model SpecificationAudio Input Humidity Troubleshooting Issue Check for the followingAccessing Planar’s Technical Support Website Index OPS expansion slot installation Iii