NAD L 70 owner manual Input Selector

Page 12

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA

Setup

SETTING UP THE L70

INPUT SELECTOR

•From the OSD’s <MAIN MENU> screen, select the <INPUT SELECTOR> menu item using the HTR L70

remotes’ and “Enter” keys.

• Using the keys select the video input (DVD, SAT, VCR, and VIDEO 4) you wish to configure.

•Use the keys to move to the <Audio> line, and then use the keys to select the analog audio input you wish to be linked to that input (usually, this will be the same, i.e., “VCR” with “VCR,” “Video 4” with “Video 4,” and so on).

NOTE

It is not necessary to have an analog audio input connected for every video input you employ. In fact, in some cases-for example for a CAB/SAT-it may be preferable to make only a coaxial or optical digital audio link to the L70 for audio playback. This avoids possible confusion, and ensures that the L70’s high-performance surround and digital audio circuitry will always be employed.

•Now use the keys to move to the <DIGITAL INPUT> line and select the digital input you wish linked to that input.

•If you set <DIGITAL INPUT> to “ANALOG,” no incoming digital signal will be selected by that input. (Set an input’s <DIGITAL INPUT> to “ANALOG” only if you wish to ensure that that input will not play an incoming digital bit stream, even if one is present.)

NOTE

•The combination of analog-audio input and digital input assigned above will always be recalled whenever that input is selected via the front-panel INPUT SELECTOR, or the HTR L70 remote’s input- select keys.

•That signals from digital inputs are not available on the analog VCR OUT jacks.

12

Image 12

Contents DVD Receiver Safety Precautions IntroductionThis Product to Rain or Moisture Record Your Model Number NOW, While YOU can see ITTable of Contents Getting the Most from the NAD L70 About the HTR L70 System Remote Control Ease of USEUpgradability QuickstartIdentification of controls Front PanelJacks of the VCR Rear Panel Español Italiano Português Svenska Important Note Setup Setting UP the L70Getting Started Dealing with HUM and NoiseSetting L70 OSD Language Receiver Section only Input SetupDisplaying the L70 RECEIVER’S OSD Navigating the OSD and Making ChangesInput Selector Speaker Configuration Setting Speaker ConfigurationSurround Mode Level Trim Test SetupSetting Level Trim Delay TimeSetting Speaker Delay Time Using the L70 Adjusting the VolumeOperation Selecting SourcesUsing the L70’S DVD/VCD/CD Press OPEN/CLOSE the Disc Tray OpensAbout DVD/SVCD/VCD/CD Region Management InformationDisc Language Settings OSD OSD NavigationVideo OSD TV DisplayPassword DefaultsSystem OSD OSD LanguageUsing the L70’S AM/FM Radio Choosing the FM Mute / Mode About RDSViewing RDS Text About User NamesAbout the L70’S Surround Modes EarsEnhanced Stereo StereoDolby Digital / DTS Selecting Surround ModesAdjusting Surround Modes DTS Delay TimeDolby Digital Delay Time Enhanced Stereo / Ears Delay TimeAdjusting Level Trim on the FLY To Adjust Level TrimAdjusting the Tone Controls About the 12 V Trigger OUTUsing the HTR L70 Remote Control SpecificationsControlling the L70 Cancel Operation Learning Codes from Other RemotesExample Learning VCR Pause PUNCH-THROUGHCopy a Command from Another KEY Macro CommandsKey Recording MacrosKEY-ILLUMINATION Timeout Factory ResetDelete Mode Executing MacrosSearch Mode Loading CODE-LIBRARIESMode Keys To Press for 3 seconds Checking CODE-LIBRARY NumberSummary of HTR L70 Modes Troubleshooting ReferenceSpecifications Physical SpecificationsAmplifier Section Tuner SectionReference L70 Manual 03/05 China