Alpine TMX-R705 owner manual Polarity, Door SW

Page 18

1Dome Override (Always OFF) (Gray/Green) Connecting to Pin #1 of the external dome light SW. When it is grounded, the Dome light remains off all the time.

2Dome Override (Always ON) (Red/Green) Connect to Pin #3 of the external dome light SW. When it is grounded, the Dome light remains on all the time.

3Dome Light (Door Trigger) (Blue/Green) Connect to the factory door switch.

NOTES

Have the switching done being the power cord taken off.

Have the switching done accurately. If you make mistakes in setting, the dome light remains lit, and it may cause running down of the battery.

Vehicle Door polarity depending on the vehicle type can be changed by the "Door SW polarity" where is located on the left side of the main unit. (Default:

Negative Switched System)

POLARITY

NEG

 

 

DOOR SW

POS

 

 

Positive Switched System

Negative Switched System

 

+12V

GND

GND

+12V

4Remote Turn ON (Blue/White) Connecting to other device such as a small amplifier to turn them ON synchronizing with the TMX-R705 power ON. It gives +12V when the power is ON.

5GND (Black)

This is a common Ground for the main unit and the Dome light. Another GND line connects to Pin #2 of the external dome light SW.

6BATT (Dome Light) (Yellow/Green)

This is a constant +12V for the Dome light. Connect to the Dome light +12V line on the

vehicle.

7BATT (Main Unit) (Yellow)

This is a constant + 12V for the main unit. It is recommended that separate connections from the Dome light battery line are used to avoid noise and over-current.

8Fuse Holder (5A)

9KWE-508V (Included)

pKWE-508V (Sold Separately)

qIGN/ACC (Red)

This wire connects to the ignition or accessory line of the vehicle. This triggers main power to turn the unit on. Although both DIN cables have this wire, only one of them should be connected to the IGN/ACC line.

wGND (Black)

This is the shield GND. It should connect to the vehicle's chassis for reducing any noise.

eExternal AV Select (Pink/Blue)

External AV Select forces the TMX-R705 to switch to the A/V input sending the AV Select trigger.

rIR Remote Out (White/Brown)

The Remote Out wire connects to any ALPINE Mobile Video product which has an external remote input function. For example, products such as a DVD, VCR and TV Tuner.

tAV RCA Connector (Video, Audio R, Audio L) These RCA-type connectors connect to any video source. This connector is used as an A/V input for the TMX-R705, however it may also be used as an output for other units.

yRemote Control Lead (White/Brown)

uRCA Extension Cable (Included with DVD changer)

iRCA Extension Cable (Sold Separately)

oAi-NET Cable (Included with DVD changer)

FR

ES

DE

IT

SE

17-EN

Image 18
Contents TMX-R705 Contents Minimize Display Viewing While Driving USE this Product for Mobile 12V ApplicationsPrecautions Halt USE Immediately if a Problem AppearsBasic Operations Parts Names of the Overhead MonitorOpening the Monitor Display Closing the Monitor DisplaySwitching the Source Adjusting the Monitor Viewing AngleAdjusting the Volume Audio Mute FunctionSwitching Display Modes Mode 1 WideOther Useful Features Adjusting Tint of Picture Adjusting Brightness of PictureSetting the Brightness of the Backlight Adjusting the Lowest Level of the Backlight Setting Automatic Closing MonitorDome Light Settings Battery Replacement Replacing the Dome Light BulbSpecifications InformationCase of Difficulty Installation and Connections Do not Install the Monitor Near the Passenger Seat AIR BAGPrecautions Mounting Instruction Connections To other MonitorPolarity Door SWLimited Warranty