AOC i2340Ve manual Setup Stand & Base, Remove

Page 10

Setup Stand & Base

Setup Stand & Base

Please setup or remove the base following the steps as below.

Setup:

Remove:

10

Image 10

Contents c 2010 AOC.All Rights Reserved Installation SafetyPower CleaningWarranty Statement for North & South America excluding Brazil ServiceWarranty Statement for Europe EPEAT DeclarationSafety National ConventionsPower Installation Cleaning Other Setup Contents in BoxPlease setup or remove the base following the steps as below Setup Setup Stand & BaseRemove Adjusting Viewing Angle Connecting the Monitor Setting Optimal Resolution AdjustingWindows Vista 5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 byFor Windows XP Windows XP5 Click SETTINGS 2 Click CONTROL PANEL 3 Click Appearance and Themes2 Click SETTINGS 3 Click CONTROL PANEL Windows ME/2000For Windows ME/2000 e-sensor HotkeysSource/Auto Menu/EnterOSD Setting Basic and simple instruction on the control keysPress Menu to display menu Press or to select to enter, and press or to adjust Press to exitLuminance Luminance, and press to enter Press or to select submenu, pressAdjust to Gamma Backlight AdjustmentAdjust to Gamma1 Enable dynamic contrast ratioadjust Press to exit Image SetupSetup , and press Press Menu to display menureduce Press Menu to display menu Press or to select Color Color TemperatureTemperature, and press to enter Press or to select submenu, press Normal CoolColor Color BoostBoost , and press Disable or Enable Green Field Mode Disable or Enable Full Enhance ModeDisable or Enable Nature Skin Mode Disable or Enable Sky-blue ModePress Menu to display MENU Press or to select Picture Picture BoostBoost and press to enter Adjust Frame Contrast Adjust Frame SizeAdjust Frame Brightness Adjust Frame horizontal PositionOSD Setup Adjust the vertical position of OSD OSD SetupAdjust the horizontal position of TimeoutExtra Analog AutoDigital Press Menu to display menu Press or to select Reset, and Resetpress to enter Press or to select YES or NO Press to exit Reset Reset the menu to defaultPress Menu to display menu Press or to select Exit and Exitpress to enter Status LED IndicatorFull Power Mode LED ColorMonitor Driver DriverWindows 5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 7.Click the “Driver” tab “Update Driver... “and then9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced Settings5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next button3. Select and click on the category „Appearance and Themes‟ 1. Start Windows XP2. Click on the Start button and then click on Control Panel 4. Click on the Display Item6. Select Monitor tab 5. Select the Settings tab then click on the Advanced button7. Click on the Driver tab and then click on Update Driver... button If the Properties button is active, click on Properties button12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Power LED Is Not ON TroubleshootProblem & Question Ghosting Shadowing ProblemMonitor Is Stuck In Active Specification General SpecificationPreset Display Modes Pin Assignments Plug and Play Plug & Play DDC2B FeatureRegulation FCC NoticeWEEE Declaration For Germany EPEAT DeclarationOnly for North and South American, excluding Brazil For BrazilService Warranty Statement for EuropeInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil BOLIVIA http//bo.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterARGENTINA http//ar.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter