AOC i2340Ve manual Click Update Driver... in the Driver tab

Page 42

5. Click "Update Driver..." in the "Driver" tab.

4.Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is.

If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".

5. Click "Update Driver..." in the "Driver" tab.

6.Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".

7.Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F:\Driver (CD-ROM Drive).

8.Select your monitor model and click on the 'Next' button.

9.Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.

Image 42

Contents c 2010 AOC.All Rights Reserved Installation SafetyPower CleaningWarranty Statement for North & South America excluding Brazil ServiceWarranty Statement for Europe EPEAT DeclarationSafety National ConventionsPower Installation Cleaning Other Setup Contents in BoxSetup Stand & Base Please setup or remove the base following the steps as below SetupRemove Adjusting Viewing Angle Connecting the Monitor Adjusting Setting Optimal ResolutionWindows Vista 5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 byFor Windows XP Windows XP5 Click SETTINGS 2 Click CONTROL PANEL 3 Click Appearance and ThemesWindows ME/2000 2 Click SETTINGS 3 Click CONTROL PANELFor Windows ME/2000 e-sensor HotkeysSource/Auto Menu/EnterOSD Setting Basic and simple instruction on the control keysPress Menu to display menu Press or to select to enter, and press or to adjust Press to exitLuminance Luminance, and press to enter Press or to select submenu, pressAdjust to Gamma Backlight AdjustmentAdjust to Gamma1 Enable dynamic contrast ratioadjust Press to exit Image SetupSetup , and press Press Menu to display menureduce Color Temperature Press Menu to display menu Press or to select ColorTemperature, and press to enter Press or to select submenu, press Normal CoolColor Boost ColorBoost , and press Disable or Enable Green Field Mode Disable or Enable Full Enhance ModeDisable or Enable Nature Skin Mode Disable or Enable Sky-blue ModePicture Boost Press Menu to display MENU Press or to select PictureBoost and press to enter Adjust Frame Contrast Adjust Frame SizeAdjust Frame Brightness Adjust Frame horizontal PositionOSD Setup Adjust the vertical position of OSD OSD SetupAdjust the horizontal position of TimeoutExtra Auto AnalogDigital Reset Press Menu to display menu Press or to select Reset, andpress to enter Press or to select YES or NO Press to exit Reset Reset the menu to defaultExit Press Menu to display menu Press or to select Exit andpress to enter Status LED IndicatorFull Power Mode LED ColorDriver Monitor DriverWindows 4.Ckick on the “Change display settings” button 5.Click the “Advanced Settings” button6.Click the “Monitor” tab and then click the “Properties” button “Update Driver... “and then 7.Click the “Driver” tab9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced Settings5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next button3. Select and click on the category „Appearance and Themes‟ 1. Start Windows XP2. Click on the Start button and then click on Control Panel 4. Click on the Display Item6. Select Monitor tab 5. Select the Settings tab then click on the Advanced button7. Click on the Driver tab and then click on Update Driver... button If the Properties button is active, click on Properties button11. Click on the Open button, then click the OK button 12. Select your monitor model and click on the Next button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Power LED Is Not ON TroubleshootProblem & Question Ghosting Shadowing ProblemMonitor Is Stuck In Active Specification General SpecificationPreset Display Modes Pin Assignments Plug and Play Plug & Play DDC2B FeatureRegulation FCC NoticeWEEE Declaration For Germany EPEAT DeclarationOnly for North and South American, excluding Brazil For BrazilService Warranty Statement for EuropeInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil BOLIVIA http//bo.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterARGENTINA http//ar.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter