AOC i2340Ve manual General Specification

Page 53

Specification

Specification

General Specification

Panel

Resolution

Physical

Characteristics

Environmental

Product name

Driving system

Viewable Image Size

Pixel pitch

Video

Separate Sync.

Display Color

Dot Clock

Horizontal scan range

Horizontal scan Size(Maximum)

Vertical scan range

Vertical scan Size(Maximum)

Optimal preset resolution

Highest preset resolution

Plug & Play

Input Connector

Input Video Signal

Power Source

Power Consumption

Off Timer

Connector Type

Signal Cable Type

Dimensions & Weight:

Height (with base)

Width

Depth

Weight (monitor only)

Temperature:

Operating

Non-Operating

Humidity:

i2340Ve

TFT Color LCD

58.42 cm diagonal

0.2652 mm(H) x 0.2652 mm(V)

R, G, B Analog lnterface & Digital Interface

H/V TTL

16.7M Colors

148.5 MHz

30 kHz - 83 kHz

509.184mm

56 Hz - 75 Hz

286.416mm

1920x1080(60 Hz)

1920x1080(60 Hz)

VESA DDC2B/CI

D-Sub 15pin & DVI-D

Analog: 0.7Vp-p(standard), 75 OHM,

TMDS

12Vdc,3.75A

Active < 35W (TYPE)

Standby < 1 W

0~24hours Select timing to turn off the monitor.

15-pin Mini D-Sub & DVI-D Detachable

585.6mm

425.2mm

190mm 3.8kg

0° to 40°

-25°to +55°

53

Image 53

Contents c 2010 AOC.All Rights Reserved Power SafetyInstallation CleaningWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil EPEAT DeclarationNational Conventions SafetyPower Installation Cleaning Other Contents in Box SetupRemove Setup Stand & BasePlease setup or remove the base following the steps as below Setup Adjusting Viewing Angle Connecting the Monitor Windows Vista AdjustingSetting Optimal Resolution 6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings5 Click SETTINGS Windows XPFor Windows XP 2 Click CONTROL PANEL 3 Click Appearance and ThemesFor Windows ME/2000 Windows ME/20002 Click SETTINGS 3 Click CONTROL PANEL Source/Auto Hotkeyse-sensor Menu/EnterBasic and simple instruction on the control keys OSD SettingLuminance to enter, and press or to adjust Press to exitPress Menu to display menu Press or to select Luminance, and press to enter Press or to select submenu, pressAdjust to Gamma1 Backlight AdjustmentAdjust to Gamma Enable dynamic contrast ratioSetup , and press Image Setupadjust Press to exit Press Menu to display menureduce Temperature, and press to enter Press or to select submenu, press Color TemperaturePress Menu to display menu Press or to select Color Cool NormalBoost , and press Color BoostColor Disable or Enable Nature Skin Mode Disable or Enable Full Enhance ModeDisable or Enable Green Field Mode Disable or Enable Sky-blue ModeBoost and press to enter Picture BoostPress Menu to display MENU Press or to select Picture Adjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal PositionOSD Setup Adjust the horizontal position of OSD SetupAdjust the vertical position of OSD TimeoutExtra Digital AutoAnalog press to enter Press or to select YES or NO Press to exit ResetPress Menu to display menu Press or to select Reset, and Reset the menu to default Resetpress to enter ExitPress Menu to display menu Press or to select Exit and Full Power Mode LED IndicatorStatus LED ColorWindows DriverMonitor Driver 6.Click the “Monitor” tab and then click the “Properties” button 4.Ckick on the “Change display settings” button5.Click the “Advanced Settings” button 9. Select Let me pick from a list of device drivers on my computer “Update Driver... “and then7.Click the “Driver” tab 13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category „Appearance and Themes‟ 4. Click on the Display Item7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button13. Click on the Finish button then the Close button 11. Click on the Open button, then click the OK button12. Select your monitor model and click on the Next button Windows ME i-Menu e-Sensor e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active General Specification SpecificationPreset Display Modes Pin Assignments Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Only for North and South American, excluding Brazil EPEAT DeclarationFor Germany For BrazilWarranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterBOLIVIA http//bo.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter