AOC i2340Ve manual Regulation, FCC Notice

Page 57

Regulation

FCC Notice

FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

NOTICE :

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to correct such interference.

57

Image 57

Contents c 2010 AOC.All Rights Reserved Power SafetyInstallation CleaningWarranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil EPEAT DeclarationNational Conventions SafetyPower Installation Cleaning Other Contents in Box SetupSetup Stand & Base Please setup or remove the base following the steps as below SetupRemove Adjusting Viewing Angle Connecting the Monitor Adjusting Setting Optimal ResolutionWindows Vista 6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings5 Click SETTINGS Windows XPFor Windows XP 2 Click CONTROL PANEL 3 Click Appearance and ThemesWindows ME/2000 2 Click SETTINGS 3 Click CONTROL PANELFor Windows ME/2000 Source/Auto Hotkeyse-sensor Menu/EnterBasic and simple instruction on the control keys OSD SettingLuminance to enter, and press or to adjust Press to exitPress Menu to display menu Press or to select Luminance, and press to enter Press or to select submenu, pressAdjust to Gamma1 Backlight AdjustmentAdjust to Gamma Enable dynamic contrast ratioSetup , and press Image Setupadjust Press to exit Press Menu to display menureduce Color Temperature Press Menu to display menu Press or to select ColorTemperature, and press to enter Press or to select submenu, press Cool NormalColor Boost ColorBoost , and press Disable or Enable Nature Skin Mode Disable or Enable Full Enhance ModeDisable or Enable Green Field Mode Disable or Enable Sky-blue ModePicture Boost Press Menu to display MENU Press or to select PictureBoost and press to enter Adjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal PositionOSD Setup Adjust the horizontal position of OSD SetupAdjust the vertical position of OSD TimeoutExtra Auto AnalogDigital Reset Press Menu to display menu Press or to select Reset, andpress to enter Press or to select YES or NO Press to exit Reset the menu to default ResetExit Press Menu to display menu Press or to select Exit andpress to enter Full Power Mode LED IndicatorStatus LED ColorDriver Monitor DriverWindows 4.Ckick on the “Change display settings” button 5.Click the “Advanced Settings” button6.Click the “Monitor” tab and then click the “Properties” button “Update Driver... “and then 7.Click the “Driver” tab9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category „Appearance and Themes‟ 4. Click on the Display Item7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button11. Click on the Open button, then click the OK button 12. Select your monitor model and click on the Next button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active General Specification SpecificationPreset Display Modes Pin Assignments Plug & Play DDC2B Feature Plug and PlayFCC Notice RegulationWEEE Declaration Only for North and South American, excluding Brazil EPEAT DeclarationFor Germany For BrazilWarranty Statement for Europe ServiceInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterBOLIVIA http//bo.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter