AOC i2340Ve manual Monitor Is Stuck In Active

Page 52

	The Computer Power Switch should be in the ON position.
	The Computer Video Card should be snugly fitted in its slot.
	Make sure the monitor's video cable is properly connected to the computer.
Monitor Is Stuck In Active	Inspect the monitor's video cable and make sure no pin is bent.
Off-Mode"	Make sure your computer is operational by hitting the CAPS LOCK key on
	the keyboard while observing the CAPS LOCK LED. The LED should either
	turn ON or OFF after hitting the CAPS LOCK key.

Missing one of the primary	Inspect the monitor's video cable and make sure that no pin is damaged.
colors (RED, GREEN, or	Make sure the monitor's video cable is properly connected to the computer.
BLUE)

Screen image is not centered	Adjust H-Position and V-Position or press hot-key (AUTO).
or sized properly

Picture has color defects	Adjust RGB color or select desired color temperature.
(white does not look white)

Horizontal or vertical	Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and
disturbances on the screen	FOCUS.
	Press to auto-adjust.

52

Image 52

Contents c 2010 AOC.All Rights Reserved Safety PowerInstallation CleaningService Warranty Statement for EuropeWarranty Statement for North & South America excluding Brazil EPEAT DeclarationSafety National ConventionsPower Installation Cleaning Other Setup Contents in BoxPlease setup or remove the base following the steps as below Setup Setup Stand & BaseRemove Adjusting Viewing Angle Connecting the Monitor Setting Optimal Resolution AdjustingWindows Vista 5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 byWindows XP 5 Click SETTINGSFor Windows XP 2 Click CONTROL PANEL 3 Click Appearance and Themes2 Click SETTINGS 3 Click CONTROL PANEL Windows ME/2000For Windows ME/2000 Hotkeys Source/Autoe-sensor Menu/EnterOSD Setting Basic and simple instruction on the control keysto enter, and press or to adjust Press to exit LuminancePress Menu to display menu Press or to select Luminance, and press to enter Press or to select submenu, pressBacklight Adjustment Adjust to Gamma1Adjust to Gamma Enable dynamic contrast ratioImage Setup Setup , and pressadjust Press to exit Press Menu to display menureduce Press Menu to display menu Press or to select Color Color TemperatureTemperature, and press to enter Press or to select submenu, press Normal CoolColor Color BoostBoost , and press Disable or Enable Full Enhance Mode Disable or Enable Nature Skin ModeDisable or Enable Green Field Mode Disable or Enable Sky-blue ModePress Menu to display MENU Press or to select Picture Picture BoostBoost and press to enter Adjust Frame Size Adjust Frame BrightnessAdjust Frame Contrast Adjust Frame horizontal PositionOSD Setup OSD Setup Adjust the horizontal position ofAdjust the vertical position of OSD TimeoutExtra Analog AutoDigital Press Menu to display menu Press or to select Reset, and Resetpress to enter Press or to select YES or NO Press to exit Reset Reset the menu to defaultPress Menu to display menu Press or to select Exit and Exitpress to enter LED Indicator Full Power ModeStatus LED ColorMonitor Driver DriverWindows 5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 7.Click the “Driver” tab “Update Driver... “and then9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced Settings5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next button1. Start Windows XP 2. Click on the Start button and then click on Control Panel3. Select and click on the category „Appearance and Themes‟ 4. Click on the Display Item5. Select the Settings tab then click on the Advanced button 7. Click on the Driver tab and then click on Update Driver... button6. Select Monitor tab If the Properties button is active, click on Properties button12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Troubleshoot Problem & QuestionPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active Specification General SpecificationPreset Display Modes Pin Assignments Plug and Play Plug & Play DDC2B FeatureRegulation FCC NoticeWEEE Declaration EPEAT Declaration Only for North and South American, excluding BrazilFor Germany For BrazilService Warranty Statement for EuropeInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil USA http//us.aoc.com/support/findservicecenter ARGENTINA http//ar.aoc.com/support/findservicecenterBOLIVIA http//bo.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter