JVC KD-AVX1 service manual Packing materials and accessories parts list

Page 60

Packing materials and accessories parts list

Block No.

No additional / supplemental order of WARRANTY CARDs are available.

M 3 M M

P2	A1 A3	P2	A1	P2
	A4		A1	A1 A3
	A4

U,A version

P1

	A20 A21
P2	A22 A23

	J version
	P2	P7
	P2	A2
		A2

U,E,A version

UT,UN version

A14

P6

A13

P3

KIT: A5 A6 A7

A8 A9 A10

A11

A12

P5

P4

A15

Jversion

P2

Eversion

P8

A16

A1A3 A4 A17 A18 A19

3-20

Image 60

Contents KD-AVX1 Specification For Northern America versionFor Europe version PALFor Asia & Australia version Audio Amplifier SectionSection Precautions Preventing static electricity Grounding to prevent damage by static electricityHandling the traverse unit optical pickup Reproduction and Position of Labels Important for laser productsSection Specific Service Instructions Main body section Removing the panel assembly See Removing the side heat sink See ReferenceSide heat sink Removing the top chassis assembly See Figs.3 to Remove the panel assembly and side heat sinkRemoving the front chassis assembly See Removing the DVD mechanism assembly See Figs.8Removing the loading unit assembly See Removing the front bracket assembly SeeCN962 Front bracket assembly Removing the main sub board SeeRemoving the connector board See Figs.13 to Detach lever Connector coverRemoving the main board See Figs.16 Removing the panel switch board See Removing the rear bracket SeeRear heat sink Rear bracket Removing the switch board See Figs.20 Removing the panel board See Figs.20CN582 Short-circuit points Removing the top cover See Removing the mechanism section See toRemoving the clamper unit See to Reattaching the clamper unit See toClamper unit Clamper spring Notch 20 No.MA165 Removing the front unit See to Removing the loading arm assembly See Removing the rod LR/roller assembly See Removing the DVD pickup assembly See to Removing the feed motor assembly See Removing the spindle motor SeeTest instruments required for adjustment Connection procedureConnection method Standard measuring conditions Adjustment method for jitter Adjustment procedureJitter value conversion table D8CAService mode Standard input/output conditions Service mode setting procedureOperation procedures Service Mode Ntsc Running Mode DVD check mode Service MODE4 RDS S Mode Monitor S ModeMechanism error code Error code tablesRunning mode Writing method for micon ROM correctionPower on Insert the disc which a farm was written in at Update method of firm wareMonitor adjustment ChromaSection Troubleshooting 16 PIN Cord Diagram for E version16 PIN Cord Diagram for A, J, U, UN, UT version No.MA1651-39VPT Parts List Exploded view of general assembly and parts list 133 131 132 General Assembly Panel Assy DVD mechanism assembly and parts list DVD mechanism Thrust Spring QYSPSFT2040ZA TAP Screw Electrical parts list QERF1HM-225Z Capacitor QERF1HM-104Z Capacitor Part Name Description Local R231 NRSA63J-104X NRSA63J-2R2X MG Resistor Panel board NDC31HJ-2R0X Capacitor 16W J R601 NRSA63J-121X Connector board NEAF0GM-227X Capacitor SW4 Packing materials and accessories parts list Packing and Accessories Schematic Diagrams Safety precaution M O Block diagram Version Standard schematic diagrams Main amplifier sectionSheet Panel-A section GDC-RS456 Panel-B section MA2SV03-XSheet Connecting section SheetSheet DVD servo control section TubuyakiTo CN965 Sheet Printed circuit boards Main boardReverse side Panel board CN521 R483 C475 R482 C474 R481 R480 C470 C485 L472 IC585 Connector board M O Front end board IC301 No.MA165SCH