Kenwood TS-B2000 $4RIT/SUB control, $5MANUAL BC control, $6MAIN RF Gain control, 0SUB SQL control

4 GETTING ACQUAINTED

54

55 45 46 44 47

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE

9.6k STA CON

PF
F LOCK	A
ATT	PRE
LEVEL
	LEVEL
VOX
	PROC
SEND	ANT1/2
	AT
PHONES	LEVEL
	N
	.
	R
	.
	LEVEL
	A
	.
	N
	.
MIC	MANUAL
	B
	.
	C
	.
	LO/
	WIDTH

CH1/REC	CH2/REC	CH3/REC
1	2
		3
TONE/SEL
	METER	CTCSS/SEL
4	5
		6
NB/LEVEL
	AGC/OFF
7	8	FINE/STEP
		9
.
DCS/SEL	SHIFT/OFFSET
	0	ENT
	HI/
	SHIFT

C N U F

MAIN
	AUTO
CAR	LSB
MIC	USB

TX MONI	REV
PWR	CW
	FSK
DELAY	NAR
KEY	FM
	AM
CLR		SEL
DISP		1MHz

							RIT
							ALT
							XIT
								_
							CLEAR
							P.C.T
							SET
		SUB			UAL	BC		MAIN
								GAIN
					MAN		RF
				QUICK MEMO
MENU		TF-		MR	M.IN
			CALL	C
		SET		.
				IN
					TL
					SA
				M/S	REV
						MAIN
	MAIN	SUB		A/B	SPLIT
					TRACE
				VFO/CH				AF
					A=B
				VFO/M
CTRL		SG.SEL		MG.SEL	M.IN			SQL
	SCAN		M VFO

RIT/SUB

+

MULTI CH

SUB

52 53

48 49 50 51

$4RIT/SUB control

After switching the RIT or XIT function ON, turn this control to select the desired frequency offset {pages 38, 40}.

Turn to adjust the sub-receiver frequency when the RIT and XIT functions are switched OFF and the sub- receiver is switched ON {page 45}.

$5MANUAL BC control

Turn to adjust the audio notch frequency while the DSP beat cancel function is set to the manual frequency adjustment mode {page 56}.

$6MAIN RF GAIN control

Turn to adjust the radio frequency gain for the main transceiver {page 18}.

$7MULTI/ CH control

In VFO mode, rotate to step the operating frequency up or down {page 37}. In memory channel mode, rotate to select a memory channel {page 58}. Also used for selecting Menu numbers when accessing the Menu mode {page 21} and as a selector to choose settings for various functions activated by front panel buttons. The MULTI/ CH LED lights when the setting(s) can be changed using the MULTI/ CH control.

$8MAIN SQL control

Used for muting (“squelching”) the speaker, the head phones and AF output on ACC2 (13-pin DIN connector) when no receive signal is present on the main transceiver {page 19}.

$9MAIN AF control

Turn to adjust the volume on the main transceiver {page 19}.

%0SUB SQL control

Used for muting (“squelching”) the speaker, head phone and AF output on ACC2 (13-pin DIN connector) when no receive signal is present on the sub-receiver {page 46}.

%1SUB AF control

Press to switch the sub-receiver ON or OFF. When it is ON, the SUB-receiver LED lights orange.

Turn to adjust the volume for the sub-receiver.

%2LO/ WIDTH control

Turn clockwise/ counterclockwise to increase/ decrease the value for the low cut-off DSP filter frequency or the filter bandwidth (CW/ FSK). The selected value appears on the main dot-matrix display {page 55}.

%3HI/ SHIFT control

Turn clockwise/ counterclockwise to increase/ decrease the value for the high cut-off DSP filter frequency or the Shift frequency. The selected value appears on the sub dot-matrix display {page 55}.

%4MAIN band LED

Lights green while the main transceiver’s squelch is open. Lights red while transmitting on the main transceiver’s VFO band.

%5SUB band LED

Lights green while the sub-receiver’s squelch is open. Lights red while transmitting on the sub-receiver’s VFO band.

12