Kenwood TS-2000X, TS-B2000 instruction manual Getting Acquainted

4 GETTING ACQUAINTED

16

CW TUNE

9.6k STA CON

PF
F LOCK	A
ATT	PRE
LEVEL
	LEVEL
VOX
	PROC
SEND	ANT1/2
	AT
PHONES	LEVEL
	N
	.
	R
	.
	LEVEL
	A
	.
	N
	.
MIC	MANUAL
	B
	.
	C
	.
	LO/
	WIDTH

						MAIN
CH1/REC			CH2/REC	CH3/REC			AUTO
1
			2	3	C	CAR	LSB
TON	E/SEL
			METER	CTCSS/SEL		MIC	USB
					N
4			5		U
				6	F	TX MONI	REV
NB/LEVEL
			AGC/OFF FINE			PWR	CW
7			8	/STEP			FSK
				9		DELAY
DCS/SEL							NAR
		SHIFT/OFFSET
	.					KEY	FM
			0
				ENT			AM
			HI/
			SHIFT			CLR	SEL
						DISP		1MHz
			14	15		18

17

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000

RIT

ALT

							XIT
								_
							CLEAR
							P.C.T
							SET
		SUB			NUAL	BC		MAIN
								GAIN
					MA		RF
				QUICK MEMO
MENU		TF-		MR	M.IN
			CALL	C
		SET		IN
				.
					SATL
				M/S	REV
						IN
					SPLIT
	MAIN	SUB		A/B		MA
					TRACE
				VFO/CH				AF
					A=B
				VFO/M
		SG.SEL		MG.SEL				SQL
CTRL	SCAN		M VFO M.IN

RIT/SUB

+

MULTI	CH
SUB

!4Multi-purpose keypad

Consists of 10 keys that are used to enter numeric data. Also used for the following functions:

•1/ CH1/REC, 2/ CH2/REC, and 3/ CH3/REC keys

Press to play back or record the CW or voice messages that are associated with the DRU-3A Digital Recording Unit {page 89} and the internal electronic keyer {page 43}.

•4/ TONE/SEL key

Press to activate the sub-audible Tone function to access repeaters for FM mode. To select the Tone frequency, press [FUNC], [4/ TONE/SEL], then select your desired tone frequency using the MULTI/ CH control {page 33}.

•5/ METER key

Press to select the meter scales {page 19}.

•6/ CTCSS/SEL key

Press to activate the Continuous Tone Coded Squelch System (CTCSS) function for FM mode. To select the CTCSS tone frequency, press [FUNC], [5/ CTCSS/SEL], then select your desired CTCSS tone frequency using the MULTI/ CH control {page 35}.

•7/ NB/LEVEL key

Press to switch the Noise Blanker ON or OFF. Press [FUNC], [7/ NB/LEVEL] to adjust the Noise Blanker level {page 57}.

•8/ AGC/OFF key

Press to adjust the response time of the Automatic Gain Control. To switch the AGC OFF, press [FUNC], [8/ AGC/OFF] {page 38}.

•9/ FINE/STEP key

Press to activate the Fine tuning mode to allow more precise tuning {page 38}.

••/ DCS/SELkey

Press to activate the Digital Coded Squelch function for FM mode. To select the DCS code, press [FUNC], [•/ DCS/SEL], then select your desired code using the MULTI/ CH control {page 36}.

•0/ SHIFT/OFFSET key

Press to switch the Shift function for FM mode ON or OFF when accessing the repeaters. The Shift frequency can be manually adjusted by pressing [FUNC], [0/ SHIFT/OFFSET], then adjusting the shift frequency value using the MULTI/ CH control {page 32}.

•ENT key

Press to enter your desired frequency using the keypad {page 37}.

!5FUNC key

Press to access the secondary functions that are assigned to the keys. While FUNC is active, the FUNC LED lights orange.

!6MIC/ CAR key

Press to adjust the microphone gain {page 20}. While the Speech Processor function is ON, it becomes the Speech Processor output level adjustment key {page 40}.

Press [FUNC], [MIC/ CAR] to adjust the carrier level for CW, FSK and AM mode {page 20}.

!7PWR/ TX MONI key

Press to adjust the output power {page 20}. Press [FUNC], [PWR/ TX MONI] to monitor your transmission signal {page 79}.

!8KEY/ DELAY key

Press to adjust the internal electronic keyer speed. Press [FUNC], [KEY/ DELAY] to adjust the VOX delay time or break-in time (Full break-in/ Semi break-in time) for CW mode {page 42}.

9