Alpine CDA-9856 owner manual Installation and Connections, 29-EN

Page 31

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 and 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury.

If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

Precautions

Be sure to disconnect the cable from the (–) battery post before installing your CDA-9856. This will reduce any chance of damage to the unit in case of a short-circuit.

Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9856 to the fuse box, make sure the fuse for the intended circuit of the CDA-9856 has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your Alpine dealer.

The CDA-9856 uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized Alpine dealer for assistance.

Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

SERIAL NUMBER:

 

 

Please record the serial number of your unit in the space provided

INSTALLATION DATE:

 

 

below and keep it as a permanent record. The serial number or the

INSTALLATION TECHNICIAN:

 

 

engraved serial number is located on the bottom of the unit.

PLACE OF PURCHASE:

 

 

 

 

 

 

 

 

29-EN

Image 31
Contents CDA-9856 CHM-S630 CHA-S634 CHA-1214 Alpine CD Changers Give You MoreContents Operating Instructions Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW About the alphanumeric display of this unit Turning Power On and OffPress SOURCE/POWER to turn on the unit Getting StartedInitial System Start-Up Adjusting VolumeLowering Volume Quickly Setting TimeRadio Manual Storing of Station PresetsAutomatic Memory of Station Presets Tuning to Preset StationsFrequency Search Function Switching the HD Radio signalPlayback X. Random Play Repeat Play10-EN About MP3/WMA Searching from CD TextFile/Folder Name Search Concerning MP3/WMA Quick Search12-EN TerminologySetting the Bass Control Sound SettingLeft and Right/Fader Between Front Rear/Defeat Setting the Treble Level Setting the Treble ControlSetting the BBE Mode Setting the Treble Center FrequencyDisplaying the Text Other Functions15-EN Press Title repeatedly until the time is displayed Displaying Time16-EN About TextVisual Customizing Sound Customizing17-EN 18-EN External DeviceChecking the SAT Radio ID Number Setting the Tuning MethodSAT Radio Receiver Optional Receiving Channels with the SAT Radio Receiver OptionalQuick Search Function Storing Channel PresetsReceiving Stored Channels Category/Channel Search FunctionXM or Sirius mode, press Title Setting the Auxiliary Data Field DisplayChanging the Display 21-ENSearching by artist name IPod OptionalSearching for a desired Song Searching by Playlist23-EN Select Playlist/Artist/AlbumSearching by album name Searching by song name24-EN Random Play Shuffle M.I.XMulti-Changer Selection Optional Changer OptionalPlaying MP3 Files with the CD Changer Optional Controlling CD Changer OptionalCase of Difficulty InformationIndication for CD Changer Indication for SAT Receiver Mode27-EN Indication for iPod Mode Specifications28-EN 29-EN Installation and Connections30-EN InstallationAccessory List Install the detachable front panel RemovalJapanese CAR 31-EN32-EN Connections33-EN Page