,______ _
| I | 48 |
| • | or:::::JD |
|
| I |
|
| |||
Note: | I |
|
|
|
|
|
Black squares indicate the | I |
|
|
|
|
|
positions ofthe switches. | I |
|
|
|
|
|
Remarque: |
|
|
|
|
| |
I |
|
|
|
|
| |
Les carres noirs indiquent les | I |
|
|
|
|
|
positions des se/ecteurs. |
|
|
|
|
| |
I |
|
|
|
|
| |
Nota: |
|
|
|
|
| |
I |
| ~ | ~ |
|
| |
Los cuadros negros indican |
|
|
| |||
las posiciones de los | I |
| . | ~ |
|
|
I |
| ·~~P~'r | or:::::JD |
| ||
interruptores. |
|
| ||||
|
| |||||
Fig.S |
Note:
SWITCH SETTINGS (Fig. 5 and Fig. 6)
e. e High Pass Filter Frequency Selector Switches
a)Slide switches 1 and 2 to the up position to turn off HP filter on front or
12rear channels [DEFAULT setting]
OFF
b)Slide switch 1 to the down position and
~switch 2 to the up position to set the
12cutoff frequency to 60Hz on front or rear
60Hzchannels
c)Slide switch 1 to the up position and switch 2 to the down position to set the
12 cutoff frequency to 80Hz on front or rear
60Hzchannels.
d) Slide switches 1 and 2 to the down position to set the cutoff frequency to
1 2120Hz on front or rear channels 120Hz
e Input Configuration Switch
2CH | a) Slide switch to the down position for 4 |
~ | channel input [DEFAULT setting] |
b) Slide switch to the up position for 2 |
5channel input
4CH
Note:
Input Configuration Switch should be in the up position for 2 CH bridged output system.
•Input Signal Type Switch
RCA | a) Slide switch to the up position for RCA | |
~ | input signals [DEFAULT setting] | |
SPKR. | ||
b) Slide switch to the down position for | ||
speaker level input signals |
•· 8 Input Gain Adjustment Control
Set the
When using speaker level inputs, both fro nt and rear gain controls should be between minimum and 9 o'clock positionfor typical head unit volume
Remarque:
Si des entrees du niveau de haut-
parleur sont uti/isees, /es controles
du gain avant et arriere doivent etre entre les positions minimales et 9 heures pour Ia gamme de volume typique de /'unite principale.
Nota:
AI usar entradas a nivel de bocina, ambos controles de ganancia deberim estar entre una posiciOn minima y
Ia posicion de las 9 en punto para
/ograr una gama de volumen tipica del
amplificador principal.
1 GAIN 1 | ~ : =: |
1 FRONT 1 |
|
h0- l | lWJ l ~l |
~~r | r ~ |
until the output distorts. Then, reduce the volume 1 step (or until the output is no longer distorted). Now, increase the amplifier gain until the sound from the speakers become distorted . Reduce the gain slightly so the sound is no longer distorted to achieve the optimum gain setting.
CONNECTION CHECKLIST (Fig. 7)
Fig.6 | |||
| I |
|
|
| ~® | ||
| - I | (J) |
|
® ®
@
Please check your head unit for the conditions listed below: (Fig. 7)
a.The head unit does not have a remote
b.The head unit'spower antenna lead is activated only when
the radio is on (turns off in the tape or CD Mode) .
c. The head unit'spower antenna lead is logic level output
(+)5V, negative trigger (grounding type), or cannot sustain
(+)12V when connected to other equipment in addition to the vehicle'spower antenna. If any of the above conditions exist, the remote
If this is objectionable, a SPST (Single Pole, Single Throw) switch, in addition to the 3A fuse mentioned above, may be installed
(j)Blue/White
~ Power Antenna
@ Remote
® To other Alpine components'Remote
@ r=usa(3A) | . _ . | __ | .. _ _ |
(/)As close as possible to the vehicle'signition tap @ Ignition Source
Fig. 7