Audiovox VM9411 instruction manual Preparation, Features, Tools and Supplies

VM9411

PREPARATION

Congratulations on your purchase of the Jensen VM9411 Mobile Multimedia Receiver.

It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9411 installed by a reputable installation shop.

Features

MULTI-ZONE

Allows up front passengers to listen to the radio while rear passengers listen to a CD, MP3, WMA or watch DVDs

DVD

•Compatible formats: DVD-R, DVD-RW, DVD+R, DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD, VCD and MPEG1, MPEG2 and JPEG

•Region 1 playback

•16:9 Aspect ratio- Wide / Normal / Cinema

•Front panel DVD control

•High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X

•Play, Pause, Stop, Slow

•Chapter Up / Down

•MultiZone output 'Kid-Zone'

•Wolfson Microelectronics high performance 24-bit, 192 kHz DAC supports 6-channel and 2-channel "Down-Mix” audio modes

•16Mbit high-speed flash memory - 80nS access time

MP3/WMA

•GIGA MP3 - Store up to 999 MP3 files on a DVD

•ID3-tag compatible

•Direct track access

•Play, Pause, Stop, Track Up / Down

•100 second (MP3), 200 second (WMA) ESP - Electronic Skip Protection

CD

•CD-text compatible

•4 second ESP - Electronic Skip Protection

AM/FM Tuner

•US/Euro/Latin/Asia Tuner

•30 Station presets (18FM/12AM)

•JENSEN Plus Tuner II

Outboard Media Module

•Input adaptor for TV Tuner, XM Radio and iPod

TV Tuner (Included)

•VHF 2-13

•UHF 14-69

•TV antenna - (3.5mm antenna included)

•F-Connector/Coaxial Antenna Input (optional)

XM Ready

•Requires optional Terk XMD1000 tuner box

•Requires optional Terk XMDJEN100 or Jensen JXMC XM cables

•Advanced display shows the artist, song title, and XM channel and category at a glance

•Direct Channel entry

jLink Ready

•Controls and charges all iPod's except "Shuffle"

•Displays all text information including category, track name, artist and channel number

Chassis

•7-inch TFT active-matrix LCD - 336,960 pixels (1440W X 234H)

•Full automatic motorized TFT LCD flip-out and up

•16-step TFT LCD tilt adjustment

•Beep Tone confirmation

•Heat management system - Incorporates forced air- cooling to keep the chip-sets operating at nominal temperatures

•Heavy duty galvanized chassis

General

•Full function infrared remote control

•Limited function infrared "Kid Zone" remote

•1 NTSC composite video output for additional screens

•OSD- On Screen Display menu control

•High performance audio processor

•Electronic volume, bass, treble, balance and fader

•Bass center frequency adjustment - 60, 80, 100, 130, 150 and 200Hz

•Bass Q factor - 1.0, 1.25, 1.5 and 2.0

•Treble center frequency adjustment - 10, 12.5, 15 and 17kHz

•Subwoofer crossover - 80, 120 and 160Hz

•Subwoofer Phase - 0 - 180 degrees

•Subwoofer level - variable

•100-ohm low impedance preamp outputs - all channels

•5V Peak / 2V RMS RCA outputs - all channels

•1-pair Front RCA outputs

•1-pair Rear / Surround RCA outputs

•Single Subwoofer RCA output

•Center Channel RCA output

•1-pair Headphone / Multi-ZONE RCA outputs

•1-pair Auxiliary RCA A/V inputs

•Back-up camera input with reverse override

•Flex fader

•Front panel (when screen is closed) high contrast LCD

•Rotary encoder audio control

•Joystick menu navigation

Tools and Supplies

You will need these tools and supplies to install your VM9411:

•Torx type, flat-head and Philips screwdrivers

•Wire cutters and strippers

•Tools to remove existing radio (screwdriver, socket wrench set or other tools)

•Electrical tape

•Crimping tool

•Volt meter/test light

•Crimp connections

•18 gauge wire for power connections

•16 – 18 gauge speaker wire

WARNING! Only connect the unit to a12-volt power supply with proper grounding.

WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions.

WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law.

WARNING! Never disassemble or adjust the unit.

WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water.

WARNING! Never use irregular discs.

WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor.

WARNING! Using an improper fuse may cause damage to the unit and result in a fire.

1