Alpine alpine owner manual About Power supply wires, Extending beyond the terminal

Page 9

 

CAUTION

 

2. Remove the insulation from the ends of the wire

attery

 

leads by about 7 – 10 mm (9/32” – 13/32”).

positive

 

(Fig. 7)

About Power supply wires

ehicle’s

 

t. See

If the length of the power and ground cables

Lead end side of the product

nimum

exceed 1 m, or if you connect more than one

 

 

amplifier, a distribution block should be used. See

 

/21 mm2

below for wire gauge recommendations for

EN

 

distribution block connection to battery and

 

ground (depends upon wire length necessary):

 

7 – 10 mm

re metal

2 AWG (33 mm2) or 1/0 AWG (53 mm2)

point to

 

 

(9/32” – 13/32”)

 

 

 

uity

 

 

FR

all your

PDR-V75

 

 

 

 

the

BATTERY

GROUND

Fig. 7

eeping

 

 

 

1 m

 

ES

 

 

NOTES:

 

(Max.)

4 AWG

If length of the exposed wire is too short, a poor

/21 mm2

 

 

(21 mm2)

connection may occur causing operation failure

y)

 

 

or sound interruption.

 

 

On the other hand, if the length is too long, an

 

 

 

ur head

 

 

electrical short-circuit may occur.

 

 

 

able, see

 

 

3. Tighten the set screw with the hexagon wrench

 

Distribution

 

 

 

 

(included) to secure the lead. (Fig. 8)

 

 

 

 

 

Before making this connection, use insulated

 

block

 

 

 

 

 

 

 

 

2 AWG (33 mm2) or

shrink tubing to cover any exposed wire

eads of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/0 AWG (53 mm2)

extending beyond the terminal.

you do

 

 

 

 

 

 

 

 

Hexagon Screw

 

 

 

 

 

 

 

 

on lead,

 

 

 

 

 

 

 

 

 

To vehicle’s

To vehicle’s

 

ion of

 

battery

chassis

Wire Terminal

NG”

 

 

 

 

 

 

 

Fig. 6

 

the

 

 

 

 

 

 

 

 

e,

Connect all equipment to the same ground point while

 

 

 

y

keeping wire length as short as possible.

 

Ensure that you install a correctly-rated in-line fuse

Wire

 

 

on the power cable near the battery positive post.

Fig. 8

 

Cautions on wire lead connections

 

 

 

When using third-party wire cables (power supply

NOTES:

 

wire), use the supplied screws to simplify the

 

Use only the screws included.

 

connection. Refer to the description below for the

 

For safety reasons, connect the battery leads last.

 

proper procedure. If you are in doubt about how to

 

To prevent disconnection of the leads or

 

make this connection, consult your dealer.

 

dropping of the unit, do not use the cabling to

 

 

 

 

 

 

 

 

 

 

1. Check the wire size.

 

 

 

 

carry the unit.

Required Wire Size

Battery Lead/Ground Lead....4 AWG (21 mm2)

Remote Turn-On Lead.............12 AWG (3 mm2)

Speaker Output Lead:

SUB W.............................................. 8 AWG (8 mm2) CH-1/2/3/4 ..................................12 AWG (3 mm2)

If the wire gauge used is unknown, ask your dealer.

7-EN

ALPINE PDR-V75 68-25285Z56-A (EN/FR/ES)

Image 9
Contents Alpine PDR-V75 68-25285Z56-A EN/FR/ES Léalo antes de utilizar este equipoAlpine PDR-V75 68-25285Z56-A EN/FR/ES English ContentsAccessories Service CareImportant Notice For European CustomersInstallation Und to ingAnty Which States r dealer ge SET CON Attaching the TOP Cover and Logo PlateTo prevent external noise from entering the audio system ConnectionsUSE the Correct Ampere Rating When Replacing Fuses Extending beyond the terminal About Power supply wiresCross Connection Check ListCrossover Mode Selector Switch Switch SettingsInput Gain Adjustment Control Input Channel Selector SwitchBass EQ Adjustment Knob Input Channel Selector Switch SUB WSpea Typical System Connections System DiagramsLine ou CH-3Important Tips on Bridging an Amplifier Bridged ConnectionsSUB W SpecificationsBlessures, voire la mort AvertissementAccessoires Service APRÈS-VENTEAvis Important Pour les clients EuropéensVeillez à ne pas endommager la zone de l’indicateur Percer les trous pour les visRemarque Fixation DU Couvercle Supérieur ET DE LA Plaque DU Logo Connexions Utiliser DES Fusibles DE L’AMPERAGE Approprie Propos des câbles d’alimentation Précautions avec les connexions des fils conducteursRemarques Liste DE Vérification DES Connexions Conducteur de mise sous tension télécommandéeRÉG COM RemarqRéglages DE Commutateur Ce mode nécessite une source à 4 canauxBouton de réglage de la fréquence de transfert Commutateur sélecteur du canal d’entréeCommutateur sélecteur du canal d’entrée SUB W DIAUnité Normal Rouge clignotant La température deConnexions Typiques DU Système Diagrammes DU SystèmeTrée Un rée à Sur ux des entrées Éhicule Inez laConn Connexions Pontées Performances SpécificationsAdvertencia ÍndiceComponentes del sistema, ya que contiene De las instrucciones de estos manualesAccesorios Cuidados PrácticosAviso Importante ImportanteNota InstalaciónColocación DE LA Tapa Superior Y LA Placa DEL Logotipo Para evitar que entre ruido externo en el sistema de audio ConexionesClavijas RCA de entrada Terminales de salida del altavozUtilice EL Amperaje Correcto Cuando Cambie Fusibles Terminal de suministro de energíaPunto el RadoPor NotasLista DE Comprobación DE Conexiones AJU InteCable para encendido remoto Ajustes DEL Interruptor Interruptor de selector de canal de entradaFiltro subsónico Interruptor de selector de canal de entrada SUB W Botón de ajuste del Bass EQConexiones Típicas DEL Sistema Diagramas DEL SistemaTrada Tá en la as12-ES Conexiones Puenteadas Rendimiento Especificaciones
Related manuals
Manual 26 pages 58.49 Kb

alpine specifications

Alpine Linux is a security-oriented, lightweight Linux distribution that is designed primarily for use in servers, embedded systems, and containers. Its unique features and technological prowess make it a compelling choice for developers and system administrators looking for a minimalistic yet powerful operating system.

One of the main characteristics of Alpine Linux is its incredible lightness. The default installation typically occupies less than 130 MB of disk space, making it ideal for container environments where efficiency is critical. This minimal footprint allows users to run high-density applications and services on the same hardware, optimizing resource utilization.

Alpine employs the musl libc and busybox, further contributing to its lightweight nature. Musl is a standard library for C that is designed to be simple, efficient, and small, while busybox consolidates several common Unix utilities into a single executable, reducing overhead and improving performance. This choice of libraries and tools allows Alpine to maintain a high level of performance while keeping the system size minimal.

Another standout feature of Alpine Linux is its focus on security. The distribution follows a rigorous security model, including a hardened kernel and various security enhancements. Notably, Alpine uses position-independent executables and stack-smashing protection to help mitigate buffer overflow attacks. Additionally, it employs a package management system that utilizes APK (Alpine Package Keeper) to facilitate secure and efficient package installation, removal, and upgrades.

Alpine's package ecosystem is another key aspect of its appeal. The Alpine Community frequently updates packages to ensure they are current and secure. The use of a rolling release model means users can always access the latest software versions without the need to perform major upgrades frequently.

Alpine Linux is also designed with ease of use in mind, featuring a straightforward installation process and a user-friendly configuration interface. The availability of various pre-built package repositories allows users to find and install the software they need without hassle.

In summary, Alpine Linux combines a lightweight design, robust security measures, and a flexible package management system, making it an ideal choice for a range of applications from cloud computing to local development environments. Its growing community and active development further enhance its attractiveness as a modern Linux distribution.