Sony KV-36FS200 Problem Possible Solutions Cable stations, Don’t seem to work, Remote control

Page 51

 

 

 

Other Information

Problem

Possible Solutions

 

 

Cable stations

❏ Make sure Cable is set to On in the Channel Setup menu (page 27).

don’t seem to work

❏ Perform Auto Program to add channels that are not presently in the

 

memory (page 17).

 

 

Remote control

❏ Press TV (FUNCTION) when operating your TV.

does not operate

❏ Check the orientation of the batteries.

 

❏ Batteries could be weak. Replace them (page 2).

 

❏ Move the TV three to four feet away from fluorescent lights.

Cannot change

❏ Make sure you have not inadvertently switched your TV from the

channels with the

channel 3 or 4 setting if you are using another device to change channels.

remote control

❏ If you are using another device to control channels, be sure that you have

 

pressed the FUNCTION button for that device. For example, if you are

 

using your VCR to control channels, be sure to press the VCR/DVD

 

FUNCTION buttons (page 4).

Cannot access

❏ If you use the

button to close the Basic menu, only the Basic menu

other menus when

appears when you press

again. To access the other menus, select the

using the Basic

Advanced Menu option (page 37).

menu

 

 

 

The remote control

❏ Press the TV FUNCTION button. You may have inadvertently pressed

doesn’t work in PIP

the VCR/DVD FUNCTION button, which changes the PIP buttons to

mode

VCR mode (page 20).

 

There is no window

❏ Be sure your PIP window picture is set to a video source/channel that has

picture or it is just

a program airing.

 

 

static

❏ You may be tuned to a video input with nothing connected to it. Try

 

cycling through your video inputs using the yellow PIP TV/VIDEO

 

button with the red dot (page 21).

I get the same program in the window picture as in the main picture

❏Both may be set to the same channel. Try changing channels in either the main picture or the window picture (page 20).

❏Your TV may be set up to select all your channels through a cable box. The cable box will only unscramble one signal at a time, so you cannot use the PIP feature. If possible, run a direct cable to the VHF/UHF jack on your TV. This will only work if your cable system provides an unscrambled signal (page 9).

I cannot get

❏ Be sure that you did not set the video label in the Setup menu (page 36)

anything but TV

to skip your video inputs. If a video input has been set to “Skip”, it will

 

be skipped when pressing the TV/Video buttons for either the main or

 

PIP pictures.

 

 

The TV needs to be

❏ Clean the TV with a soft dry cloth. Never use strong solvents such as

cleaned

thinner or benzine, which might damage the finish of the cabinet.

 

 

43

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Operating Instructions Page Protecting the TV Owner’s RecordTrademarks and Copyrights Accessories Use Power SourcesCleaning InstallationSafety Check Power-Cord ProtectionService Damage Requiring Service Replacement PartsPage Contents Page Introduction Introducing the FD Trinitron Wega FeaturesOperating Instructions Batteries for the Remote ControlAbout this Manual Front Panel Menu ControlsIntroduction Using the Remote ControlTV/VIDEO Unscrambled cable channels Picture quality when you need to switch between scrambledTV Rear Panel Jack DescriptionSystem Connecting Your TV JackDescriptionJacks provide better picture quality than the VHF/UHF jack Connects to the Audio LMONO, R input jacks on your audioBasic Connections TV with Indoor or Outdoor Antenna, or Catv CableNot supplied Page Page Optional connection Connecting Additional EquipmentConnecting a TV and VCR Connecting Your TVConnecting a TV, VCR, and Cable Box Rear of TV SplitterCable Box Connecting a TV and Satellite Receiver Connecting Your TV Optional connectionRear of TV Connecting a TV, Satellite Receiver, and VCR Rear of TV Rear of DVD Player Connecting a DVD PlayerConnecting an Audio System Connecting a CamcorderPage Setting Up the TV Automatically To reset the TV to factory settingsTo perform Auto Program again Menu Allows you to Make adjustments to your picture settingsCustomize your channel settings Quick Start to the MenusUsing Basic Functions Menu Allows you to To check your PIP Using Picture in Picture PIPDisplaying Picture in Picture To use PIPTo change channels/programs in the PIP window Using Basic FunctionsPIP Functions buttons Yellow labeled Description PIP buttonSetups that affect your ability to use PIP How to access menus Using the MenusUsing the Video Menu Using the Audio Menu Operating Instructions Audio Out Using the Channel Setup Menu Favorite ChannelsCable Label Operating Instructions Auto ProgramChannel Skip/AddUsing the Parent Menu To access the Parent menu, refer to the following stepsTo use the Parent Menu Select a Country Setting the RatingChanging your Password Parental ControlTo view a program that exceeds the TV rating Using the Custom MenuPress , then use the 0 9 buttons to enter your password Information for ParentsUnited States Selecting Custom Rating Options Movie RatingTV Rating Unrated AllowBlock A. Rating Canada Selecting Custom Rating OptionsEnglish Rating French RatingTimer Using the Timer MenuTo access the Timer menu, refer to the following steps Timer 1Using the Setup Menu Use the g to increase picture contrast Using the Basic MenuTo access the Basic menu, refer to the following steps Press G to decrease picture contrastPage VCR codes Programming the Remote ControlLaser Disc Player codes Operating Instructions VCR codesCable box codes Satellite receiver codesOperating a Laser Disc Press To Other InformationOperating a VCR Press To Operating a DVD Press ToTroubleshooting Using the Basic Problem Possible Solutions Cable stationsRemote control Cannot accessYou lost your After disconnectingTV and timer LED flashes Parental ControlFor all models except as noted SpecificationsKV-36FS100, KV36FS200 Index Page Page Page Page Page Page Page Page Sony Corporation
Related manuals
Manual 64 pages 12.57 Kb Manual 64 pages 12.58 Kb
Top Page Image Contents