Network Technologies RACKMUX-T15 ON-SCREEN Display OSD, Standard Controls, OSD Control Menu

Page 44

NTI RACKMUX RACKMOUNT ANSI TERMINAL DRAWER

8. ON-SCREEN DISPLAY (OSD)

8.1 Standard Controls

The RACKMUX LCD has 5 standard control buttons and a power LED. The 5 standard control buttons operate as follows:

•The Power button turns the RACKMUX LCD and backlight ON and OFF as desired.

•The Power LED located immediately below the Power button is a dual color

LED. It will illuminate with a green color when the RACKMUX is powered

Power

ON and working properly. It will illuminate with a red color if the RACKMUX

ON/OFF

is powered ON but there is no input signal detected. The LED will

Power LED

illuminate red only momentarily just before turning OFF.

 

 

• The Menu button is used to bring up the OSD menu where the various

 

Menu

 

Up Arrow

settings of the LCD display can be adjusted. Once the OSD screen is

 

displayed, the Menu button is used to make selections within the menus.

 

 

See "OSD Control Menu " (below) for more on LCD display settings.

Down Arrow

Controls for the OSD Menus

•The Up and Down Arrow buttons are used to navigate through the menus. Move the cursor up or down as desired to highlight an item for selection. Once an item is highlighted, pressing the Menu button will select it.

Select/

Auto Adjust

Figure 7- OSD Controls

•The Select button is used to make selections within the OSD menus when

the OSD menu is ON. When the OSD menu is OFF, the Select button will act as an Auto Adjust button to keep the user from having to use the menus to adjust the quality of the image on the monitor.

8.2 OSD Control Menu

The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the OSD Menu, press the Menu button (above). To turn the Menu back OFF, either select "EXIT" from the main menu or just wait 10-60 seconds and it will automatically be cleared from the screen.

8.2.1 OSD Main Menu

Selection

Purpose

Brightness/Contrast

Increase/decrease panel brightness/contrast level

Color

R,G,B color temperature control

Position

•

Auto Adjust

 

• Video Image horizontal and vertical position control

 

•

Clock setting

 

•

Phase control

Setup

• Control OSD Image position on screen

 

• Set time OSD will stay on screen before auto shutoff

 

• Select the language of the OSD menu

Exit

Exit from the OSD control menu

Range 1-1001-100

1-100

--

10 to 60 seconds

Several languages (see page 40)

40

Page 43 Page 45
Image 44
Page 43 Page 45
Contents RACKMUX-T15 Trademark Table of Contents Table of Figures Features IntroductionMultiple RS-232 Emulations CompatibilityMaterials Supplied with this kit MaterialsOptions Features and Functions Standard Rack InstallationRack Mounting Instructions Optional Telco 2-Post Mounting Mount to Telco post with optional mounting bracketsConnect The Cables Connect a CPU to the RackmuxHow To Setup The Terminal Power Up The TerminalUsing the Rackmux Default Configuration Disp Setup Menu F2 General Setup MenuF4 Comm Setup Menu F5 Misc Setup Menu F3 Keybd Setup MenuChanging The Operating Parameters F1- Disp Setup MenuF2- Genrl Setup Menu Printer F3- Keybd Setup MenuF4- Comm Setup Menu F5- Misc Setup Menu F7- FKeys SET-UP Definition Setup MenuF6-Tabs SET-UP Menu Printer RCV ON/OFFF9- Lan Setup Menu F8- Ansbk SET-UP MenuF10- Colr1 Set-up Menu Programmable KeysColor Association = OFF/ON Color Setup Menu F11- Colr2 Set-up MenuAttribute = Bold/Blink OptionColor Palettes Palette Display Attribute Foreground Color Background ColorColor Palettes Contd Local Keyboard Commands Command Enhanced PCPin Signal Direction Connector PIN AssignmentPin Signal Mnemonic Direction Command Guide Commands Supported in Ascii PersonalitiesSame WyseNative Mode Wyse Select bell volumeStop parity word Key/fkey DELSequence DEL Key/fkey Sequence Sequence DELESC . cursor1 Message CRESC a mf attr AttrFcolor Bcolor mapCcc C ColLine col Sending data Editing ContdClearing Data Print Functions Character SetsSet Pp bb...bbVariable Values for Commands Function Key Unshifted Shifted FunctionKey Unshifted Shifted Handshaking ProtocolSpace DefinitionMax Maximum Speed Screen Area*eBell Volume Function KeyPalette Color Pallette Parity BitsAnsi Command Guide VT100, VT220 and Console Ansi Command GuideWnd/page Window or Write-Protected Display AttributeCharacter Set Selection ESC Ps finalSame Label assignedFinal character Values for Ps aboveCharacter Attribute Ps FunctionValues for Psn in table on Editing FunctionsShifted function key VT100, VT220 Console Ansi Editing Functions ContdClear Key Lock Unshifted function key Key ValueValues of Fn for Numeric Keypad keys Numeric Value KeypadMore Terminal Control Commands Terminal ResetsAuxiliary Keypad Modes Transmission/Printer ControlVT52 Command Guide Command VT52See table below for values of Ps Keyboard LanguageUsing Printer Server in Ethernet Terminal Basic SetupSetup for LPD IntroductionLPD printing Setup for Tftp Tftp PrintingON-SCREEN Display OSD Standard ControlsOSD Control Menu OSD Main MenuPosition Menu Brightness/Contrast MenuColor Menu Setup Menu OSD Image can be moved to different points on the displayKeyboard Functions Function Key OperationNumber Pad Keys of the Number PadOther Uses of the Function Key Numeric Keypad OptionStandard Crossed End Crossover Cable Pin assignment at Wire Color Standard End Crossed EndCPU-TO-RACKMUX Ethernet Crossover Cable DC Power Option Rackmux with DC Power optionDimensional Drawings Frequently Asked Questions Questions and AnswersTechnical Specifications Index TroubleshootingWarranty Information
Top Page Image Contents