Playback messages / deleting messages, Flash time

Playback messages / deleting messages

Press button. The messages will be played one after the other. If there are new messages, only these will be played.

During playback

Press button to go to the beginning of the current message.

Press button twice to go to the previous message.

Press button to go to the next message.

Press button to pause playback (Pause), and restart playback.

Press button to stop playback (Stop).

Press button to delete the current message, press and HOLD for approxi-

mately 2 seconds until “dL” appears in the display. Press once again.

In idle state

Press button to delete all old messages (already heard), press and HOLD

for approximately 2 seconds until “dL” appears in the display. Press once again. You’ll hear a confirmation announcement

Remote access code - checking / setting

You need a 3-digit code (default 000) for remote access.

Press briefly

to check the setting.

Press and HOLD

to enter setting mode. Use

and

to set the first digit.

Press briefly

for confirmation, and to get to the next digits input. Follow this

procedure for entering the digits and confirm by pressing . You will hear a repeat confirmation of code.

Outgoing message - setting / checking / recording / deleting

Press and HOLD to select the OGM (outgoing message).

Press and HOLD until you hear a short beep. Speak your own new outgoing

message. Stop recording by pressing . You hear the new OGM.

Press briefly to check the OGM at any time.

It is only possible to select an outgoing message if the answering machine is turned on. If the memory is full, only outgoing message 2 can be selected (only answering without recording messages).

Remote access

For remote access you need a telephone using tone dialing (DTMF).

Call your number, If the answering machine is set to off it will pick up the line after 10 ring signals. If it set to on it will pick up the line after the pre-set numbers of ring signals. You hear an announcement and a beep. If you want to skip the announcement press the

button.9

Flash time

You can set the flash time to 100 ms (usually for special services of your telephone provider/delivery state) or 600 ms (e.g. for a telephone exchange). In case of questions please contact your telephone provider or the system administrator of your PBX.

Press the MENUOK button. Select BASE using / and press the MENUOK button.

Using	/	select RECALL and press the MENUOK button.	button.
Using	/	select SHORT or LONG and press the OK	button.
		MENU

Press and HOLD the REDIAL button for approximately 3 seconds. S (100ms) or L (600ms) appears in the display.

System PIN

In delivery state the PIN is set to “000”. The PIN is valid for all registered handsets.

Press the	MENUOK button. Select BASE using /	and press the MENUOK button.
Using /	select SYSTEM PIN and press the	MENUOK button. Enter the old PIN and

confirm by pressing the MENUOK button. Enter the new PIN twice and confirm each by pressing the MENUOK button.

Registering a handset

Up to five handsets can by registered to a base station. The handsets delivered with your telephone are already registered. To register a “foreign” handset please refer to it’s user manual.

Press the MENUOK button. Select REGISTER using / and press the MENUOK button. Using / select a base station to subscribe to and press the MENUOK button. Enter the base’s PIN (EM6113 base station in delivery state “000”). The phone will ask “PRESS

BASE”

Press and HOLD the paging key PAGE at the base station for approximately 10 seconds. The LED “IN USE/CHARGE” will begin to flash. After this the base station will be in registration mode for one minute.

Deleting a handset

You can delete a handset from a base to allow another handset to be registered.

NOTE: You can only remove other handset in your system but you are not able to remove the handset you are using.

Press the MENUOK button. Select DE-REGISTERusing / and press the MENUOK button. Press and HOLD the MUTE button for approximately 3 seconds. Enter the PIN for base station (EM6113 base station “000”). Enter the internal telephone number (1...5) of the handset you want to remove.