Panasonic SL-DZ1200 manual Platter setup, Setup

Page 7

Platter setup

The stoppers are used to lock the platter, protecting the unit from shock during shipping.

1.Remove the 3 platter lock stoppers from the platter

Platter lock stoppers

Turn the platter lock stop-

pers approximately 90°

Pull the platter lock stop- pers out

•Pull out the platter lock stoppers once they are aligned with the release hole.

2. Attach the slip surface (included)

Slip surface

Marker

Mounting pin

•With the marker on the slip surface facing up, attach onto the 2 mounting pins.

Store the 3 platter lock stoppers in a safe place after removal.

Adjusting the platter brake

You can adjust the platter brake speed using the BRAKE control on the rear of the unit. After connecting, adjust to the desired brake speed. ( page 14)

When transporting the unit

Make sure to re-attach the 3 platter lock stoppers.

1.Remove the slip surface

•Pack in a way to avoid bending the slip surface.

2.Insert the 3 platter lock stoppers

1.Align the platter holes with the chassis holes inside at the same position used to remove the stoppers above in step 1.

2.Insert the platter lock stoppers into the holes

•Move the platter to fully insert the stoppers.

3. Turn the platter lock stoppers approximately 90° to lock

Setup

Place the unit on a flat and stable surface that is not subject to vibrations or movement.

Note

•Do not place this unit on top of amplifiers emitting hot air or place near spot lights and use for any long duration. This may affect the unit or disc causing problems.

•Create space around this unit in order to assist heat release.

•Place the unit away from televisions and tuners to avoid interfer- ence. Interference will affect picture and sound quality.

•Placing the unit near speakers may result in undesired sound in an environment that requires elevated volume. In this case move the unit further away from the speaker(s) or turn the volume down.

•Place stereo connection cables, AC power supply cord and panel in a location that will not be affected by movement or vibration during play.

Undesirable sounds may result if there are movements or vibra- tions affecting the unit with exception of the legs.

Adjusting the height of the main unit

After placing the unit in the desired location for use, adjust the insula- tor so the main unit is flat and secure.

Changing the display angle

Change display angle corresponding to position of the main unit. ( page 11)

Before use

7

RQT7114

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Direct Drive Digital Turntable Product service Table of contentsUse Listening cautionBefore use Important Safety InstructionsRear panel Main featuresControl panel Front panelRear panel Component part namesControl panel Front panelSetup Platter setupConnections Connecting with the DJ mixerConnecting with other mixers Listening with the headphonesConnecting with the stereo amplifier Not using the DJ mixer Connecting the control terminals for relay playConnecting to equipment with digital input terminals Inserting-removing a disc or SD Memory Card Changing the display angle Display indicatorAdjusting the display contrast Displaying the remaining timePlaying CD-R and CD-RW discs Auto Cue function Turntable mode onlyTurn Volume Playing a CD or SD Memory Card basic playInsert a disc or SD Memory Card Press Power OFF onSwitch Mode to Turntable Switch Play Select to select the me- dia to be usedAdjusting the auto cue level Basic function settingsUsing the Free Wheel mode Adjusting the platter brakeAdvanced Platter operationsChanging play with your hand Basic play for DJsReverse play Reversing the platter Changing tempo and direction of playChanging tempo Locking the pitchPlay from the stored point Setting the cue point at any pointSetting the auto cue point Playing from memoryStoring to the CUE Pads and playing Playing from memoryStore desired points to memory and play loop play Recording to the Sample Pads in real-time Select play mode and playRecording to the Sample Pads and playing Erasing cue pad, sample pad, loop play dataFormance Changing the soundChanging sound to simulate analog Change sound with combined perSave the data Saving to a SD Memory Card, RecallingSaving to a SD Memory Card Insert a SD Memory CardSD Memory Card Formatting the SD Memory CardRegarding MP3 albums and SD audio Recalling loading data saved on aUsing the amplifier and other equipment Using with other equipmentStart play using the mixer’s fader Using two units for relay playInitializing this unit’s memory Unit’s initialize memory functionGlossary Linking different tracksConcerning CDs Handling SD Memory CardsReference Question Answer Frequently asked questionsTroubleshooting guide Problem Cause SolutionTo clean this unit, wipe with a soft, dry cloth Error messagesMaintenance SpecificationsLimited warranty only for U.S.A Panasonic/Technics DJ Products Limited WarrantyElectric Corporation of America Puerto Rico, Inc. PSC
Top Page Image Contents