Introduction, Features, Precautions

Introduction

Congratulations on purchasing a Gemini XL-100 turntable. This state of the art turntable includes the latest features. Prior to use, we suggest that you carefully read all the instructions.

Features

•±6% Pitch control

•Strobe illuminator

•Soft-touch start/stop switch

•Cartridge included

Precautions

1.Read all operating instructions before using this equipment.

2.To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified service technician.

3.Tone Arm bearings are factory set and sealed. Any attempt at adjustment will void the warranty.

4.Be sure that all AC power is OFF while making connections.

5.Cables should be low capacitance, shielded and of proper length. Make sure that all plugs and jacks are tight and properly connected.

6.Always begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait 8 to 10 seconds prior to turning up the speaker volume to prevent the transient “POP” that could result in speaker/crossover damage.

7.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

8.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

Parts Checklist

Turntable unit

1.First, place a screwdriver in the center of LOCKING WASHER (4C) around the CENTER SPINDLE (4) and gently pry the washer off.

2.Remove the platter and wrap the belt around the inner circle under the platter. DO NOT STRETCH OUT THE BELT.

3.Replace the platter and rotate the PLATTER (2) until the MOTOR SPINDLE (4B) is visible, then fit your fingers in hole on the top of the PLATTER (2), feel for and grab the rubber belt and attach to the motor spindle.

4.Replace the locking washer.

TURNTABLE INSTALLATION:

1.Put the RUBBER MAT (5) on the PLATTER (2).

2.Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Use the turntable feet to horizontally stabilize the unit.

3.Try to place the unit as far away from the speakers as possible.

4.Keep the unit away from direct exposure to the sun, heat, moisture or dirt.

5.Keep the unit well ventilated.

CARTRIDGE INSTALLATION: (SEE FIG. 2)

Because all cartridges have their own designs, please refer to your particular cartridge’s instructions to insure proper installation.

1.Connect the lead wires to the cartridge terminals. For your convenience, the terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color.

White	(L+)	.................Left	Channel	+
Blue	(L-)	Left	Channel	-
Red (R+)		Right	Channel	+
Green	(R-)	Right	Channel	-

2.Mount the cartridge in the HEADSHELL (6) and tighten it with the screws included with the cartridge.

ATTENTION STANTON 680 CARTRIDGE USERS

When using a Stanton 680 or similar cartridge, where the body is grounded to a cartridge terminal, remove the grounding strap from the cartridge body to the cartridge ground terminal. Failure to do this may result in excessive hum.

Dust cover hinge	............................................................................2
Turntable platter	1
45 RPM adapter	1
Rubber mat	1
Counter balance	1
Dust cover	1
Headshell	1

Assembly and Set-Up

NOTE: SEE FIG. 1 (PAGE 1) FOR PART NUMBERS AND LOCATIONS.

HEADSHELL INSTALLATION:

Insert the HEADSHELL (6) into the front of the tubular TONE ARM (7). While holding the HEADSHELL firmly in a horizontal position, turn the LOCKING NUT (8) counter clockwise until the HEADSHELL is locked in place.

COUNTERWEIGHT INSTALLATION: (SEE FIG. 3A & 3B)

1.Slide the COUNTERWEIGHT (9) onto the rear of the TONE ARM (7) with the numbered stylus gauge facing forward.

2.Twist the COUNTERWEIGHT (9) lightly counter clockwise, to screw it onto the rear of the TONE ARM (7).

ADJUSTING HORIZONTAL ZERO (0) BALANCE AND

VOLTAGE SELECTION:

STYLUS PRESSURE:

Rotate the PLATTER (2) until the VOLTAGE SELECTOR (3) (located on the TURNTABLE BASE (1)) is visible through one of the platter holes. Make sure that the VOLTAGE SELECTOR switch is set to the correct voltage. WARNING: If you try to operate the turntable with the incorrect voltage setting, it can damage your turntable.

ATTACHING THE TURNTABLE BELT:

The TURNTABLE BELT (4A) comes attached to the PLATTER (2) and the MOTOR SPINDLE (4B) but can some times detach in shipping. Rotate the PLATTER (2) and look through the platter holes to check if belt detached. If the belt is not wrapped tightly around the platter and the MOTOR SPINDLE, you need to reattach it.

1.Without touching the stylus tip, remove the stylus protector (if your cartridge has a detachable one).

2.Release the ARM CLAMP (10) and lift the TONE ARM (7) off the ARM REST (11).

3.Counter clockwise advancement of the COUNTERWEIGHT (9) will cause the cartridge side of the TONE ARM (7) to be lowered. Clockwise will cause the opposite. Turn the COUNTERWEIGHT clockwise or counter clockwise as needed until the TONE ARM is balanced horizon- tally. You can easily tell this by watching for the point where the TONE ARM “floats” freely.

4.Place TONE ARM (7) on ARM REST (11) and lock it in place with the ARM CLAMP (10).

Page 4

XL-100 specifications

The Gemini XL-100 is a cutting-edge spacecraft designed for a variety of missions, primarily targeting advanced space exploration and research. This innovative vehicle is part of a new generation of spacecraft, combining sophisticated technology with robust engineering to push the boundaries of what's possible in space travel.

One of the standout features of the Gemini XL-100 is its advanced propulsion system. Utilizing a hybrid rocket engine, it boasts a unique combination of liquid and solid propellant capabilities, which allows for greater flexibility and efficiency during flight. This propulsion system significantly reduces fuel consumption while maximizing thrust, making the Gemini XL-100 capable of reaching higher altitudes and achieving faster speeds than its predecessors.

The spacecraft is equipped with state-of-the-art avionics and navigation systems. These technologies enable real-time data processing and autonomous flight control, allowing the Gemini XL-100 to make complex maneuvers with ease. The onboard computer systems are designed to handle multiple contingencies, ensuring mission success even in unpredictable scenarios.

In terms of design, the Gemini XL-100 features a sleek aerodynamic structure made from lightweight, durable materials that provide enhanced performance in diverse atmospheric conditions. The exterior is coated with advanced thermal protection materials, ensuring the spacecraft can withstand the harsh environment of space during both launch and re-entry.

The Gemini XL-100 also prioritizes crew safety and comfort. The spacious cockpit is outfitted with high-tech displays and ergonomic seating that can accommodate up to three astronauts. The life-support systems are designed to provide a stable environment, featuring advanced air recycling and temperature control technologies.

Technologically, the Gemini XL-100 is equipped with an array of scientific instruments and communication systems. These tools allow for real-time data transmission, enabling teams on Earth to monitor experiments and conditions as they unfold in space.

Its modular payload bay can accommodate a variety of scientific instruments, satellite deployments, and exploratory equipment, making it suitable for diverse missions ranging from Earth observation to deep space exploration.

In summary, the Gemini XL-100 represents a significant leap forward in space technology, combining advanced propulsion, sophisticated avionics, and durable design to tackle the challenges of modern space missions. Its versatility and reliability make it a vital asset in the ongoing quest for knowledge and exploration beyond our planet.