Fagor America 30i-T B, 20i-T B operation manual Error codes, Eeeeeeee

Page 31

4.3 Error codes

 

Error codes

 

 

Error

Description

FAGOR dro

Power outage or turned off with main switch after saving the data.

 

 

Error 02

The unit has been turned off without previously pressing [ON/OFF]. It only looses

 

feedback reading (it resets it to zero and the status of the operating modes, inch,

 

abs, radius, etc.).

 

 

Error 04

Wrong parameter data

 

 

Error 05

Wrong internal configuration

 

 

Error 06

Errors in data backup memory (Service Dept.)

 

 

Error 07

Emergency input active. Press [CLEAR] or cancel the emergency signal.

 

 

Error 08

Wrong software memory or the software has been changed.

 

 

Error 09

Errors in work memory (Service Dept.)

Error 12

Error while searching a distance-coded reference mark (Io).

 

 

Error 31

Internal malfunction (Service Dept.).

 

 

Error 32

Internal malfunction (Service Dept.).

 

 

Error 99

Internal malfunction (Service Dept.).

 

 

. . . . . . . .

Feedback alarm coming from the feedback device (linear or rotary encoder).

 

 

1. 4. 3. 6. 5. 7. 2. 5

Feedback speed too high.

 

 

EEEEEEEE

Maximum position reading or speed exceeded when searching home.

 

If any message other than the first two from the table were to come up, the

 

equipment should be switched off and on again until one of the first two are

 

seen.

 

After pressing this key to access the counting mode, check the parameters.

 

If any of the errors shown as (Service Department) are often repeated, ask

 

Fagor Automation’s Customer Services Department about this.

 

If the display of any axis shows all its dots; for example: 1.4.3.6.5.7.2.5. It

 

means that the axis has been moved too fast (>200 KHz or 60 m/min with 1

 

µm resolution). This error will be displayed if the alarm activation parameter

 

for the axis PAR08(1) = 1

 

To clear the display, press this key.

 

If the axis value is flashing, this means that one of the travel limits established

 

by machine parameter has been exceeded. This error will be displayed if the

 

alarm activation parameter for the axis PAR08(2) = 1

 

If the DRO does not come on or goes out while running, check that the

 

voltage and ground outlets are as they should be. If there are OK, disconnect

 

the feedback connectors one by one. If the dro comes on, it means a

 

feedback failure. If the fault persists get in touch with Fagor Automation’s

 

Customer Services Department about it.

V0612 - 20i-T / 30i-T - Installation/Operation - Appendix - (31/32)

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 20i-T / 30i-T DRO operation DRO installationParameters to configure axis position reading and display DRO descriptionDescription of LEDs and keys Front panelTurning the unit on and off PrecautionsDisplay modes Page Example Incremental modeAt this point, one can proceed in two ways To preset part zero Absolute modeHome search sequence Machine Reference selection and searchDeleting all tool offsets Tool PresetTo preset a tool, just follow this procedure Operation with toolsCoordinate freeze Hold Tool preset in Hold modeSpecial operations Scaling factorTaper cone calculation To do this, follow this procedureTool change at any known point of the part Operating with the calculator Calculator= Preset Recall and Reset modesDisplay Keys Operation Installation of the built-in model DRO installationOn the back of the unit the following items may be found Rear panelUL seal Connection of the feedback systems General technical characteristicsCharacteristics of feedback inputs X1, X2 ConnectionsFeedback connection. Connectors X1, X2 Pin Signal Function Easy setupAccessing the Easy Setup mode Operating modePower and machine connection Installation parametersAxis status will then switch to one of the following Move through parameters To quit the parameter editing modeTo get into parameter editing To enter a parameterDigit Parameters to configure axis position reading and displayParameter PAR00PAR02 Factory settingPAR03 PAR09 PAR04PAR05 PAR08PAR11 Personalize Binary type home search settingPAR12, PAR13 PAR14PAR15 Multi-point leadscrew error compensationPoint Nr Position Error to be Compensated ErrorPAR53 PAR20PAR65 Electromagnetic Compatibility UL sealCE seal Declaration of conformitySafety conditions It is recommended to mount the DRO vertically Symbols that may be carried on the productElectrical shock symbol Ground Protection symbolMaterial returning terms Warranty termsEeeeeeee Error codesFagor Automation S. Coop Maintenance

30i-T, 20i-T B, 20i-T, 30i-T B specifications

Fagor America has long been recognized as a leader in providing advanced CNC (Computer Numerical Control) solutions for various industrial applications. Among its standout products are the Fagor 30i-T, 20i-T, and 20i-T B control systems, which have garnered widespread acclaim for their innovative features and versatile technologies.

The Fagor 30i-T is designed for high-performance machining applications, making it ideal for complex part production. It offers a powerful processing unit that supports high-speed machining and incorporates advanced features such as adaptive control algorithms. This technology optimizes cutting conditions in real time, leading to improved efficiency and extended tool life. The 30i-T is compatible with various machining centers and lathes, allowing for seamless integration into existing production lines.

The Fagor 20i-T brings a balance of performance and affordability, tailored for mid-range applications. This control system incorporates a user-friendly interface that simplifies operation, benefiting operators of all skill levels. It is equipped with features such as graphics-based programming, which provides operators with a visual representation of machining processes. Additionally, the 20i-T supports multiple axes and can handle simultaneous multi-axis machining, enabling the creation of intricate designs without compromising on precision.

For even more specialized applications, the Fagor 20i-T B offers enhanced capabilities for bending machines and panel saws. This model includes dedicated functions for managing bending sequences and ensuring accurate positioning, making it a favorite among fabricators. The user-friendly interface, combined with intuitive programming options, allows operators to set up and execute tasks quickly, contributing to increased production efficiency.

All models, including the 30i-T and 20i series, are designed with built-in safety features and comply with international standards, ensuring safe operation in various industrial environments. They also support various communication protocols, facilitating connectivity with different devices and systems, thus enabling easy data exchange and interoperability.

In conclusion, Fagor America's 30i-T, 20i-T, and 20i-T B control systems represent cutting-edge solutions that cater to a wide range of machining and manufacturing applications. With their emphasis on user-friendly technology, real-time optimization, and robust performance, these CNC controls are poised to enhance productivity and streamline operations for businesses in the competitive manufacturing landscape.
Top Page Image Contents