Weslo WLTL29712.0 user manual Troubleshooting, Symptom The power turns off during use

Page 16

TROUBLESHOOTING

Most treadmill problems can be solved by follow- ing the simple steps below. Find the symptom that applies, and follow the steps listed. If further assis- tance is needed, see the front cover of this manual.

SYMPTOM: The power does not turn on

a.Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a surge suppressor that meets all of the specifications described on page 9.

IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.

b.After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.

c

Tripped

Reset

SYMPTOM: The power turns off during use

a.Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console, and then reinsert it.

d.If the treadmill still will not run, please see the front cover of this manual.

SYMPTOM: The console displays remain lit when you remove the key from the console

a.The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 14 to turn off the demo mode.

SYMPTOM: The displays of the console do not function properly

a.Remove the key from the console and UNPLUG THE POWER CORD. Place the treadmill in the storage position (see HOW TO FOLD THE TREADMILL on page 15).

Remove the six indicated M4.2 x 13mm Washer Head Screws (5) and the six Foot Rail Flat Washers (25). Next, lower the Frame (50) (see HOW TO LOWER THE TREADMILL FOR USE on page 15).

5

 

50

 

25

5

 

25

 

 

5

 

5

 

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents QUESTIONS? Model No. WLTL29712.0 Serial NoCall TOLL-FREE Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedNose pliers Start all four Screws, and then tighten ThemScrews, and then tighten them Page HOW to Connect the Power Cord Operation and AdjustmentUse a Surge Suppressor Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleLeft display-As Follow your progress with the displaysMeasure your heart rate if desired HOW to USE a Preset Workout Select a preset workoutInformation Mode HOW to Change the Incline of the TreadmillHOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Symptom The power turns off during useSymptom The walking belt slows when walked on Repeat until the walking belt is centered Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart List Key No. Qty DescriptionDrawing a Exploded Drawing B Exploded Drawing C Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents