Weslo WLTL29508.0 user manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes,

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

65

20

POWER CORD. Remove the three Hood Screws (20)

and the two indicated Foot Rail Screws (25). Then,

 

 

 

carefully remove the Hood (65).

 

25

 

 

 

 

Locate the Reed Switch (89) and the Magnet (62) on

 

 

the left side of the Pulley (71). Turn the Pulley until the

1/8 in.

 

Magnet is aligned with the Reed Switch. Make sure

71

that the gap between the Magnet and the Reed

 

Switch is about 1/8 in. (3 mm). If necessary, loosen

89

62

the Reed Switch Screw (3), move the Reed Switch

slightly, and then retighten the Screw. Reattach the

Top View

 

Hood (not shown), and run the treadmill for a few min-

 

utes to check for a correct speed reading.

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents On the WEB QUESTIONS?Model No. WLTL29508.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Treadmill, and before performing the main For your benefit, read this manual carefully before Before YOU BeginAssembly Bolts 2. Do not tighten the Bolts yet See the inset drawing. Locate the wire tieHold the Left Upright 53 so that the two indi Cated small holes are on top. Attach the LeftPage Connector Steps 10 and 11. Firmly tighten all six M8 15mm Bolts If the Connectors are not CONMake sure that no wires are pinched. Start Fully tighten the Bolts yetScrews before tightening either of them HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power Follow your progress with the track and the dis- plays HOW to USE the Manual ModeInsert the key into the console Start the walking beltMeasure your heart rate if desired HOW to USE a Speed ProgramHOW to Change the Incline of the Treadmill HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Walking belt. If the walking belt has shifted to Problem The walking belt slows when walked onExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Description R1108AExploded Drawing A-Model No. WLTL29508.0 R1108A Exploded Drawing B-Model No. WLTL29508.0 R1108A Exploded Drawing C-Model No. WLTL29508.0 R1108A Exploded Drawing D-Model No. WLTL29508.0 R1108A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents