Weslo WLTL29508.0 user manual Problem The walking belt slows when walked on

Page 20
2–3 in.
Idler Roller
Bolts

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be-

come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

c.If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt has shifted to the left, first re-

 

 

 

 

 

 

move the key and UNPLUG THE POWER CORD.

 

a

 

Using the hex key, turn the left idler roller bolt clock-

 

 

 

 

 

 

wise 1/2 of a turn. Be careful not to overtighten the

 

 

 

walking belt. If the walking belt has shifted to the

 

 

 

right, turn the left idler roller bolt counterclockwise 1/2

 

 

 

of a turn. Then, plug in the power cord, insert the key,

 

 

 

and run the treadmill for a few minutes. Repeat until

 

 

 

the walking belt is centered.

 

 

 

b. If the walking belt slips when walked on, first re-

b

move the key and UNPLUG THE POWER CORD.

Using the hex key, turn both idler roller bolts clock-

 

wise, 1/4 of a turn. When the walking belt is correctly

 

tightened, you should be able to lift each edge of the

 

walking belt 2 to 3 in. (5 to 7 cm) off the walking plat-

 

form. Be careful to keep the walking belt centered.

 

Then, plug in the power cord, insert the key, and care-

 

fully walk on the treadmill for a few minutes. Repeat

 

until the walking belt is properly tightened.

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents QUESTIONS? Model No. WLTL29508.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Treadmill, and before performing the main Before YOU Begin For your benefit, read this manual carefully beforeAssembly See the inset drawing. Locate the wire tie Hold the Left Upright 53 so that the two indiCated small holes are on top. Attach the Left Bolts 2. Do not tighten the Bolts yetPage Connector If the Connectors are not CON Make sure that no wires are pinched. StartFully tighten the Bolts yet Steps 10 and 11. Firmly tighten all six M8 15mm BoltsScrews before tightening either of them PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord HOW to Turn on the Power Console DiagramFeatures of the Console HOW to USE the Manual Mode Insert the key into the consoleStart the walking belt Follow your progress with the track and the dis- playsHOW to USE a Speed Program Measure your heart rate if desiredHOW to Change the Incline of the Treadmill HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Walking belt. If the walking belt has shifted toExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R1108A DescriptionExploded Drawing A-Model No. WLTL29508.0 R1108A Exploded Drawing B-Model No. WLTL29508.0 R1108A Exploded Drawing C-Model No. WLTL29508.0 R1108A Exploded Drawing D-Model No. WLTL29508.0 R1108A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents