Weslo WLTL29321 user manual Power Cord

Page 13

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-

 

come damaged. Remove the key and

UNPLUG THE

POWER CORD

. Using the allen wrench, turn both

rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, in- sert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2”–3”

Rear Roller Adjustment Bolts

c.If the walking belt still slows when walked on, please call our toll-free Customer Service Department.

PROBLEM: The walking belt is off-center or slips when walked on

 

SOLUTION:

a. If the walking belt is off-center, first remove the key

 

 

and UNPLUG THE POWER CORD

. If the walking

 

belt has shifted to the left,

use the allen wrench to

 

turn the left rear roller bolt clockwise 1/2 of a turn;

if

 

the walking belt has shifted to the right,

turn the

 

bolt counterclockwise 1/2 of a turn. Be careful not to

 

 

overtighten the walking belt. Plug in the power cord,

 

 

insert the key and run the treadmill for a few minutes.

 

 

Repeat until the walking belt is centered.

 

 

b. If the walking belt slips when walked on, first remove

 

 

the key and

UNPLUG THE POWER CORD

. Using

 

the allen wrench, turn both rear roller bolts clockwise,

 

 

1/4 of a turn. When the walking belt is correctly tight-

 

ened, you should be able to lift each side of the walk-

 

 

ing belt 2 to 3 inches off the walking platform. Be

 

 

careful to keep the walking belt centered. Plug in the

 

 

power cord, insert the key and carefully walk on the

 

 

treadmill for a few minutes. Repeat until the walking

 

 

belt is properly tightened.

 

 

a

b

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model No. WLTL29321 Serial No QUESTIONS?Our factory Customer HOT LineImportant Precautions Table of ContentsMove the Treadmill on Never leave the treadmill unattended while itNever insert any object into any opening Before YOU Begin Using the treadmillRight Side BackAssembly Floor. Rraise the Uprights 62, 76 to the vertical position Ground Wire Large HoleUpright 62 to discharge any static Tie TiesHarness from slipping Screws used in assembly steps 2, 3,Do not overtighten the Screws.Note Make sure ScrewsPerformant Lube HOW to Plug in the Power CordThis product must be grounded.If it should malfunc Grounded Outlet BoxWater bottle in the water bottle holder Console DiagramSTEP-BY-STEP Console Operation Insert the key fully into the consoleChange the incline of the treadmill as desired Distance in either miles or kilometers seeFollow your progress with the three displays Time/Distance Fat Calories/CaloriesHOW to Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE Solution TroubleshootingUnplug the Power Cord Power Cord Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Part Identification Chart Key Qty Description R0803A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0803A
Top Page Image Contents