ASSEMBLY
Assembly requires two persons.Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with
Assembly requires the included small allen wrench | and your own phillips screwdriver | , rubber |
| |
mallet | , wire cutters | , adjustable wrenches | , and needlenose pliers | . |
For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART in the center of this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do not open the part bags until instructed to do so.
1. Make sure that the power cord is unplugged. |
| 1 |
|
|
|
|
| |
|
|
|
|
|
| 40 |
| |
|
|
|
|
|
|
|
| |
|
|
|
| 36 |
|
|
| 87 |
|
|
| 37 |
|
|
|
|
|
|
|
| 75 |
|
|
|
|
|
|
|
|
|
| 40 |
|
|
|
With the help of a second person, carefully tip the tread- | 38 | 25 |
|
|
|
| ||
|
|
|
|
|
| |||
mill onto its left side as shown. Partially fold the Frame |
|
|
|
|
|
| ||
(75) so the treadmill is more stable. | Do not fully fold the |
|
|
|
|
|
| |
treadmill until it is completely assembled. |
|
|
|
|
|
|
| |
Open part bag A. | Attach four Base Pads (40) to the |
|
|
| 40 | 87 |
| |
|
|
|
|
| ||||
|
|
|
|
|
| |||
Base (11) with two 1 1/4” Tek Screws (87) and two 3/4” | 11 |
| 40 |
|
|
| ||
Tek Screws (25). Attach a Wheel (37) to the right side of |
|
|
|
| ||||
|
| 25 |
|
|
| |||
the Base with a Wheel Bolt (36) and a Wheel Nut (38). |
|
|
|
|
| |||
|
|
|
|
|
| |||
2. See drawing 2a. Make sure that there are two |
| 2 | 2a |
| 2b |
| 47 | |
(97) in the lower end of each Upright (62, 76). |
|
| ||||||
|
|
|
|
|
| |||
Identify the Right Upright (62), which has a large round |
| 97 |
|
|
|
| ||
|
|
|
|
|
| |||
hole and a slot near the lower end. While a second per- | 76 |
|
| 62 |
|
| ||
son holds the Right Upright near the Wire Harness (21), |
|
|
|
| ||||
|
|
|
|
|
| |||
insert the end of the Wire Harness into the round hole |
|
| 62, 76 | Side View |
| |||
and out of the upper end of the Right Upright. |
|
|
|
| ||||
|
|
|
|
|
|
Open part bag B. | Slide the slot in the Right Upright (62) | 21 |
| ||
onto the Upright Lock Br | acket (47) (see drawing 2b). Slide | 62 |
| ||
the Right Upright down until it reaches the Base (11). | Make |
| |||
Slot |
| ||||
sure that the Wire Harn | ess (21) is not pin | ched. | Attach |
| |
the Right Upright to the Base with two 2 1/2” Bolts (53) |
| Round Hole |
| ||
and two Star Washers (9). |
|
| 47 |
| |
|
|
|
|
| |
With the help of a second person, tip the treadmill onto |
|
|
| ||
its other side. Attach the Left Upright (76) as described |
| 9 |
| ||
above. (Note: There is not a wire harness on the left |
|
| 53 | ||
|
|
| |||
side.) Attach the other Wheel (not shown) to the Base |
| 11 |
| ||
(11) as described in step 1. |
|
|
| ||
|
|
|
|
5