Weslo WLTL29321 user manual Floor. Rraise the Uprights 62, 76 to the vertical position, Tie Ties

Page 6

3.With the help of a second person, tip the treadmill so the Base Pads (40) (see drawing 1) are laying flat on the

floor. Rraise the Uprights (62, 76) to the vertical position.

Hold the Crossbar (34) between the Uprights (62, 76). Attach the Crossbar with two 2 1/2” Bolts (53) and two 5/16” Washers (57)Do. not tighten the Bolts yet.

4.Feed the Wire Harness (21) up into the rectangular bracket on one of the Handrails (1) and out of the large hole in the left side. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the large hole.

Remove any plastic ties from the rectangular bracket on

the Handrail (1). Insert the bracket into the upper end of the Right Upright (62). Attach the ends of the Handrail to the Right Upright with two 1” Bolts (8). Do not tighten the Bolts yet.

Attach the other Handrail (1) as described above. Note: There is not a wire harness on the left side.

Open part bag C. Attach the end of the ground wire to the small hole in the side of the right Handrail (1) with a Silver Screw (70).

5. Place the Console Base (46) on the right Handrail (1)

and the left Handrail (not shown). Touch the Right

Upright (62) to discharge any static.

Hold the Console (10) near the Console Base (46). Insert the Wire Harness (21) through the two indicated plastic ties on the Console Base. Next, insert the Wire Harness

up through the indicated opening in the Console Base

and through the plastic tie on the bottom of the Console.

Plug the widest connector on the Wire Harness (21) into

the widest connector on the Console (10). The connec- tors should slide together easily and snap into place.

If they do not, turn the connector on the Wire Harness and try again. Plug the other connector on the Wire Harness into the other connector on the Console. Note: The locations of the connectors are shown by arrows.

Securely tighten the plastic tie on the Console (10) to

prevent the Wire Harness (21) from slipping.Then, cut off the end of the plastic tie.

3

 

 

 

53

34

 

 

57

 

 

 

 

 

 

57

 

76

 

53

 

 

 

 

 

62

 

4

 

 

 

1

8

Ground

21

Wire

 

 

 

 

 

70

 

 

Large

 

8

 

Hole

 

 

1

 

 

 

76

 

Bracket

 

 

 

 

 

62

 

8

 

 

 

 

8

 

 

5

10

 

 

 

 

 

 

Tie

 

 

46

21

 

 

 

 

 

1

Ties

21

 

 

 

 

62

 

 

 

6

Image 6
Contents Our factory QUESTIONS?Model No. WLTL29321 Serial No Customer HOT LineTable of Contents Important PrecautionsNever leave the treadmill unattended while it Move the Treadmill onNever insert any object into any opening Right Side Using the treadmillBefore YOU Begin BackAssembly Upright 62 to discharge any static Ground Wire Large HoleFloor. Rraise the Uprights 62, 76 to the vertical position Tie TiesDo not overtighten the Screws.Note Make sure Screws used in assembly steps 2, 3,Harness from slipping ScrewsThis product must be grounded.If it should malfunc HOW to Plug in the Power CordPerformant Lube Grounded Outlet BoxSTEP-BY-STEP Console Operation Console DiagramWater bottle in the water bottle holder Insert the key fully into the consoleFollow your progress with the three displays Time/Distance Distance in either miles or kilometers seeChange the incline of the treadmill as desired Fat Calories/CaloriesHOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting SolutionUnplug the Power Cord Power Cord Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part Identification Chart Key Qty Description R0803A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty Part No R0803A