Weslo WATL27105.1 user manual Crossbar Screws yet

Page 8

6.Carefully pull the opposite end of the tape to pull the Wire Harness (60) up through the Right Handrail (59) and out of the hole in the side of the Right Handrail.

Remove the tape from the Wire Harness (60).

7.Orient the Crossbar (91) with the large hole at the right of the smaller hole as shown. Set the Crossbar against the Handrails (53, 59) with the brackets on the Crossbar aligned with the two small holes in each Handrail. Attach the Crossbar with two Crossbar Star Washers (93) and two Crossbar Screws (92). Do not tighten the

Crossbar Screws yet.

With the help of as second person, hold the console assembly near the Crossbar (91). Connect the pulse wire from the Crossbar to the pulse wire from the con- sole assembly. The connectors should slide easily into each other and snap into place. If they do not slide easi- ly and snap into place, turn a connector and then insert it.

Insert the ground wire through the two plastic ties shown in step 8. Attach the end of the ground wire to the small hole in the side of the Right Handrail (59) with a Silver Ground Screw (69).

8.Place the Console Base (52) on the Crossbar (91), Right Handrail (59) and the Left Handrail (not shown). Be care- ful not to pinch any wires. Attach the Console Base with four 3/4” Screws (2) (only two Screws are shown). Do not overtighten the Screws.

Insert the Wire Harness (60) through the two indicated plastic ties on the Console Base (52). Next, touch the Right Handrail (59) to discharge any static. See the inset drawing. Insert the connector on the end of the Wire Harness into the red socket beneath the console. The connector should slide easily into the socket and snap into place. If the connector does not slide easily and snap into place, turn the connector and then insert it.

Make sure that the connector and wire appear as shown in the inset drawing. IF THE CONNECTORS ARE NOT

INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

6

60

Tape

 

 

59

 

7

 

 

 

 

 

 

Console

 

 

 

Assembly

53

 

 

Ground

 

 

 

 

 

69

Wire

93

91

 

 

92

Pulse

 

 

 

Wires

 

93

 

 

59

 

 

92

 

 

 

8

52

 

 

 

60

 

 

 

Ties

91

 

2

 

 

 

 

 

59

 

60

 

 

 

 

 

 

 

Socket

8

Image 8
Contents Customer HOT Line QUESTIONS?Model No. WATL27105.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Front Right Side BackAssembly Page Crossbar Screws yet Screws and then tighten them Top ViewPRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console HOW to Turn on the PowerSelect the manual mode Access the information mode if desiredInsert the key into the console Press the Start button or the Speed increaseHOW to USE a Speed Program Measure your heart rate, if desiredWhenkey. you are finished exercising, remove Insert the key fully into the consoleMeasure your heart rate if desired When the program ends, remove the key from ConsoleHOW to Change the Incline of the Treadmill HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart Identification Chart Part LIST-Model No. WATL27105.1 Qty DescriptionNo. WATL27105.1 Shanghai Newlife Fitness Equipment, Inc HOW to Order Replacement PartsLimited Warranty